Battery Cycle
-
Product
Material Research Battery Tester
BTS9000
-
Shenzen Neware Electronic Co LTD
BTS9000 is the most advanced battery testing instrument from Neware, it's the best choice for material research, but some customers think BTS9000 is a little expensive. Thus, we developed BTS9000-2CH for people who want to get high accuracy and high speed with low price.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Lithium Battery Discharge-Charge Unit
FGCD
-
Fuzhou Fuguang Electronics Co., Ltd.
FGCD series tester adopts advanced charging and discharging technology with a variety of built-in test and maintenance modes, which are suitable for the discharge, charging and discharge-charge cycle tests of various lithium battery packs on the market.
-
Product
Battery Analyzer
UBA5-30V
-
The UBA5-30V can analyze up to 30V battery packs (33 for lithium ion or lithium polymer). It comes with a small power supply (120VAC or 220VAC input) that powers the UBA5's internal circuitry.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Heavy Impact Tester, Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery impact tester tests the safety of the battery through different weights, different heights and different impact areas. After a series of tests on this battery impact tester, the battery must not have flame or explosion.
-
Product
Power Temperature Cycling
-
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
-
Product
Cycle Drop Simulation Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Cycle drop simulation generator
-
Product
Rechargeable Battery Telemetry Systems
2100R Series
-
Advanced Telemetrics International
Offers more performance and features while providing solutions to common shaft mounted obstacles. Separate but simultaneous data and status signals allow a variety of control functions independent of the high quality data stream ATi is known for. Battery power means lower noise floors, more versatile installations, no active power generation or tuning.
-
Product
Battery Tester
TMC-2001RTS
-
The TMC-2001RTS is our newest member of advanced battery testers. We integrated in a very small and lightweight housing all facilities for modern battery and UPS maintenance. Best price/performance ratio.
-
Product
CTEK LITHIUM US Battery Charger
56-926
-
The LITHIUM US is an advanced microprocessor controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries - maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
-
Product
Battery Starting & Charging System Analyze
12-2415
-
*Shown with optional 12-2416 barcode scanner*Graphical Hand-Held Tester with Thermal Printer and USB Port*Tests 12V Flooded, AGM, Gel Cell, & EFB Batteries from 100 to 2000CCA*Graphical/Symbol Based LCD display*Tests 12/24V charging and electrical systems*Stores last 70 test series with or without power*Carrying case, printing software and USB cables included*Built-in thermal printer with thermal paper (611305)*Field-Replaceable Cables (900165)
-
Product
Battery Drop Tester for Battery Safety Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery drop tester is used to test the drop impact performance of large, heavy-duty packaging products by simulating real surface, edge, and corner differences.
-
Product
Battery Manufacturer Analyser 24V Icon
BMA24I
-
The Battery Manufacturer Analyser 24V Icon (BMA24I) is our newest innovation of battery analyser. It has colour display and intuitive graphical instructions solve language barrier and allows battery manufacturers to distribute to their distributors and dealers worldwide.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Laboratory Test Equipment Temperature Cycling Steam Aging Test Chamber
-
Shenzhen Chuangxin Instruments Co., Ltd.
Steam aging test machine is used to test and determine the parameters, performance of electrical, electronics, other products and materials for high temperature, low temperature, or the temperature of the thermostat test environmental changes.
-
Product
Battery Management Controllers
-
Renesas offers a dedicated single-package solution with an MCU and analog front end (AFE) for battery management systems that constantly monitors the battery state.
-
Product
Battery Discharger & Capacity Tester
IDCE-2415CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
Product
EIS Battery Analyzer
BA8100
-
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
Product
Battery PACK (500v-1000v)Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
PACK test equipment adopts sinexcel, firstly adopts three-level AC scheme, and the detection process supports multi-gear switching. The device integrates voltage, temperature, pressure and other auxiliary channels, and CAN also integrate various communication protocols such as temperature box, water cooler, mainstream CAN CANFD 485, etc. It supports a variety of practical and innovative functions such as data one-click automatic export, which meets all aspects of PACK battery electrical performance testing.
-
Product
Vehicle Battery Tester
6420
-
Peaceful Thriving Enterprise Co Ltd
This is a device to test the 12 volt lead-acid battery of any vehicle. The tester will focus on health condition analysis of vehicle battery; it will estimate the cold cranking ampere (CCA) of the vehicle, and predict the lifetime of the battery. This will be helpful for the technician to inspect and maintain the electrical system of the vehicle. Base on the inspection, user can predict the time to replace the battery.
-
Product
Battery Testing
-
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
Product
Automatic Battery
BATLV480
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
-
Product
CTEK Multi US 25000 Battery Charger
56-674
-
CTEK MULTI US 25000 is an 8-step, fully automatic primary switch mode battery charger. A powerful charger for 12V batteries that require rapid charging such as in garages, RV’s, boats and of course cars. Unlike old traditional battery chargers CTEK chargers are designed with focus on simplicity, safety and flexibility.
-
Product
Industrial Battery Tester
-
The Industrial Battery Tester (IBT) has been designed for testing traction batteries or batteries for stationary applications. It can also be used for testing other types of batteries. The IBT performs charging and discharging in accordance with the programmed test schedule. Parameters are constant current, constant voltage, constant resistance and constant power.
-
Product
Cell Battery Crush Test Equipment (Vertical)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Cell Battery Crush Test Equipment (Vertical)Application: Single cell crush test (cylinder, pouch, prismatic cell, etc)Crush Tool: Semi-cylinder, hemisphere (According to test standard)
-
Product
Battery Discharge and Capacity Testers
-
HD Power Test Equipment Co.ltd
HDFD Battery Discharge Tester can be used as the discharge load in the battery off-line state to realize the constant discharge at the set value by regulating continuously the discharge current. When discharging, the tester will automatically stop discharging when the voltage on the battery group terminal or the cell falls to the set lower limit value, or when the set discharging time is out, or when it reaches the set discharging capacity. Battery Discharge Tester can records all valuable and continuous real-time data during the discharge process.This tester system is simple, safe and accurate for monitoring voltage of cells adopting wireless connection.
-
Product
Battery Acid Refractometer – Sulfuric Acid Specific Gravity
H2SO4
-
Measure battery acid safer and more precisely. The MISCO Palm Abbe digital refractometer eliminates bringing acid up to your eye – a risk associated with analog/shadow line models. This refractometer has a single scale for sulfuric acid specific gravity.
-
Product
Battery Chargers
-
The JUNXY intelligent battery charger covers three charging processes: (1)Constant current charging → (2)Constant voltage with decreasing current charging→ (3)micro current floating charging. Auto shut-down when reach any one of four charge cutt-off settings: (1)cell voltage, (2)charge duration, (3)charge capacity, (4)manual stop charge. It is especially designed for battery bank maintenance for different industries with nominal voltages: 24V, 36V, 48V, 80V, 96V, 110V/120V, 220V/240V, 380V etc with different charging current.
