Pre-amplifiers
Detect and strengthen a signal prior to greater amplification.
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Programmable Current Preamplifier
99539
-
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
Product
Digital MCA Tube Base For Gamma-Ray Spectroscopy
Gamma Stream Family
-
CAEN Gamma stream is a compact and portable system for gamma ray spectroscopy with scintillation detectors, which provides an active Multi-Channel Analyzer (MCA) integrated in a 14-pin photo-multiplier tube (PMT) base. Gamma stream fully integrates in a stand-alone device the high voltage to bias the PMT, the preamplifier to shape the signal from detector, and the MCA for a complete Pulse Height Analysis online.
-
Product
CZT Gamma-Ray Detector Spectrometer
GR Family
-
The Kromek GR family is a range of CZT-based high-performance gamma-ray spectrometers. They are completely self-contained, with built-in preamplifier, shaping amplifier, baseline restorer, pulse height digitizer, and HV supply. The digitized pulse heights of detected gamma-ray signals are sent to a PC via the USB. The unit is powered entirely from the USB bus, so no external power supply is needed.
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Product
Read-Write Analyzers
-
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
Product
ELT STALKER Vector-finder
VF-121
-
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Preamplifier
-
Is designed for the amplification of measuring signals, e.g. weak signals of near field probes with high resolution.
-
Product
DC to 350 MHz Preamplifier
SR240A
-
Stanford Research Systems, Inc.
The model SR240A 350 MHz Preamplifier is a 4-channel, DC-coupled instrument with a gain of 5 per channel. The amplifiers can be used independently or cascaded to provide gains of 5, 25, 125 or 625.
-
Product
X-Ray Preamplifier Power Supply
-
The X-ray Preamplifier Power Supply (XPPS) provides power for 50 or more preamplifiers. The 19-inch rack-mount or benchtop unit contains linear power supplies that generate +/-12V @ 5.1 Amperes and +/-24V @ 3.6 Amperes, with very little noise.
-
Product
Precision Condenser Microphone
378A12
-
1/4-inch pressure prepolarized 377A12 microphone, with 1/4-inch preamplifier 426B03 and TEDS v0.9
-
Product
C-Band Single Channel Pre-Amplifier EDFA (SPA)
HSA4300 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4300 series is a low noise pre-EDFA which designed specifically for single wavelength optic transmission system. It is installed in the front of optical receiver, used for improving the receiving sensitivity of the optical receiver, and extending the signal transmission distance.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-03
-
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
Read-Write Analyzer Systems
4000 TDMR Series
-
For Two Dimensional Magnetic Recording (TDMR). The 4000 Series RWA Systems support UP12 preamplifier and the next generation front end cartridge/head amplifier designs on Guzik spinstands. Previous generation of head amplifiers together with UP11M are also supported by RWA-4000 TDMR Systems in one channel mode.
-
Product
Accessories
-
Spectrum Accessories: Cables, A/D External Pre-Amplifiers, D/A Amplifier Card, Clock and Trigger Distribution, Docking Stations
-
Product
Emissions Test System
PC-114
-
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
Product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
Product
Transducers
-
CRYSOUND offers an impressive array of sensor products, including measurement microphones, preamplifiers, artificial ear coupling cavities, and artificial mouth sound sources. These diverse products enable us to meet the specific needs of our clients with precision and innovation.
-
Product
ICP Microphone System
378C10
-
This model includes a 1/4" microphone cartridge, a mated preamplifier with TEDS, and system calibration.
-
Product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
-
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Acoustic Emission Sensors
-
Acoustic wave (acoustic emission) sensors are the ceramic piezoelectric transducers converting the mechanical elastic acoustic waves generated in the material (e.g. elastic waves occur when a material cracks, wears, deforms, or corrodes) to electrical signals. The electrical signals are then amplified and filtered by a preamplifier and then transmitted to a special acoustic emission acquisition instrument for further data processing and analysis.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer
N9936B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more
-
Product
Sound Level Meter
831-LOWN
-
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
Product
Hydrophone
TC 4037
-
Incorporating a 10dB low-noise preamplifier able to drive a 25-metre cable and a wide usable frequency range, the TC 4037 is a spherical probe hydrophone that’s ideal for measuring sounds in the 100 to 500kHz range.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 4 GHz
N9933B
-
A lightweight, durable, microwave spectrum analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Noise Figure Measurements With Vector Correction
S97029B
-
The instrument’s standard receivers are used for noise figure measurements with the S97029B. An external preamplifier and filter(s) is required for devices with < 30 dB of excess noise (gain plus noise figure in dB)
-
Product
Modular Pulse Processing Electronics
-
CAEN provides a complete and ever increasing set of instrumentation, from Preamplifiers to Data Acquisition to Triggering Electronics and Logic Functions. Most of the instrumentation is available in the most popular standard form factors and bus protocols, such as VME, NIM, CAMAC and Desktop.The Desktop is the stand alone form factor of the CAEN products. It provides the same performances of the other form factors and take the advantage of an easier and portable use, requiring no crates.
-
Product
Charge Sensitive Preamplifier-Discriminator
A101
-
Model A101 is a hybrid charge sensitive preamplifier, discriminator, and pulse shaper developed especially for instrumentation employing photomultiplier tubes, channel electron multipliers and other low capacitance charge producing detectors in the pulse counting mode. The A101 is widely used in laboratory and commercial applications for mass spectrometers, laboratory and research experiments, aerospace instrumentation, medical electronics, and electro-optical systems.
