Analog Input Output
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O Module
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
PXI 8 Slot BRIC 414x8 1-Pole Dual Analog Bus (9 sub-cards)
40-560A-121-414X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
32-CH Discrete Input Modules with U Profile
HSL-DI32-UD
Digital Input Module
HSL U series is designed as compact & horizontal-placed slave module. For I/O module, ADLINK adopts three types of connectors to meet different users' requirements & habits. Compared with past models, U series brings compact size, easier-to-wire and cost-effective advantages for users. DI/O, AI/O and motion control module are supported
-
Product
Mixed Signal Oscilloscope 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012G
Oscilloscope
The MSOX3012G 100 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
USB Modular Oscilloscope, 200 MHz, 2 Analog Channels
U2702A
Oscilloscope
200 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimplify your setup with USB plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) software
-
Product
External Input Unit for Digital Sensor
FX-CH2
-
Panasonic Industrial Devices Sales Company of America
The Panasonic External Input Unit For Digital Sensor FX-CH2 will allow external access for teaching, data bank switching and other functionality.
-
Product
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A
T3PS30063P
DC Power Supply
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A.
-
Product
RF Analog Signal Generators
-
The right solution for your requirements from the broad analog signal generator portfolio of Rohde & Schwarz.With the analog signal generator portfolio we cover the wide range of RF, microwave and mmWave frequencies.Our selection of analog signal generators is characterized by the outstanding signal purity and performance as well as their functionality of the solutions; whether in the high end or midrange area.The solutions benefit industries such as RF semiconductor, wireless communications, aerospace and defense, and also covers tasks featuring development, production and service, and more.
-
Product
Output Characteristic Analyzer of Electronic Ballast
UI2002
-
• Measure lamp voltage, lamp current, lamp power, oscillatory frequency, filament current, guided cathode current, and crest factors • Measure changing curves and values of startup lamp voltage, lamp current, filament current, cathode current from 0 to 5 seconds, as well as the pre-heat time • Accuracy: Class 2 • Data and curves printable. All the data and curves can be displayed after being connected with PC
-
Product
38.6W to 451W - Single Output
PAH Series
-
*Standard Half Brick Footprint*18-36 Vdc, 36-76 Vdc Inputs*12V 29A, 48V 9.4A Nominal Outputs*1500 Vdc Isolation*Through Hole Mounting*Constant Switching Frequency
-
Product
120 W 16.5 - 50 VDC 5 outputs PSU PCI/104 SFF
PCI104-SFF-IPSU-16-50-C
-
This rugged isolated power supply is capable of supplying up to 120 watts of power output for a range of sensitive defense applications as well as industrial applications - with conformal coating.
-
Product
16 D/A Outputs (+10 VDC or +10 mA)
DA2
-
The DA2 module features 16 D/A output channels with a full scale range of ±10 VDC at ±10 mA (max). The DA2 module also offers external trigger/synchronization signal (RS422/485) capability, which provides/accepts a trigger signal to/from other module(s).
-
Product
50 W | 11.4-36 VDC | 4 outputs | PSU PCI/104 for SFF
PCI104-SFF-IPSU-11-36-4
-
This rugged isolated power supply is capable of supplying up to 50 W of power across four (dual 5 V and dual 3.3 V) output for a range of sensitive defense applications as well as industrial applications.
-
Product
Mixed Signal Oscilloscope: 8 GHz, 4 Analog Plus 16 Digital Channels
MSOV084A
Oscilloscope
8 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.04 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Oscilloscope, 100 MHz, 2 Input Channels, 1 GS/s interleaved, 7 Mpts/Ch)
T3DSO1102
Oscilloscope
100 MHz, 500 MS/s per Ch, 1 GS/s interleaved, 2 CH, 14 Mpts/Ch DSO with 7"" Color Display.
-
Product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400C (3RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400C (3RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
Product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX3052T
Oscilloscope
500 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
FMC Card with DisplayPort Input and Output
TEF0007-02A
-
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX3054T
Oscilloscope
500 MHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
32-Ch Isolated Digital Input And 16-Ch PhotoMOS Relay USB 3.0 I/O Module
USB-5855
-
USB 3.0 SuperSpeedDaisy chainable by built in USB hub32-ch digital input and 16-ch PhotoMOS Relay output (Form A) isolationWide input voltage range (10 ~ 30 VDC)1500 VDC optical isolation for relay outputsQuick removable European type connectorLED indicators for I/O statusSupported operating systems: Windows 10/11
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Mixed Signal Oscilloscope: 20 GHz, 4 Analog Plus 16 Digital Channels
MSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Digital-To-Analog Converter
DAC-200
-
Advanced Thermal Solutions, Inc.
The DAC-200 is a digital-to-analog converter designed to convert the output of the ATVS family of instruments to 0-5VDC. The device produces an output whereby the voltage is linearly proportional to both the air velocity and temperature for the ATVS product family, including the ATVS-Nxt, ATVS-2020, eATVS-4, eATVS-8, and iQ-200.
-
Product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
Oscilloscope 40 GHz, 4 Channels, 1.85 mm Inputs
UXR0404B
Oscilloscope
XR0404B Infiniium UXR-Series is the 40 GHz, 4 channel, 1.85 mm input, Infiniium UXR-Series real-time oscilloscope.
-
Product
1000W to 1500W - Single Output
RWS-B/ME Series
-
*Medical certification (IEC60601-1)*2 x MOPP*10 Year e-cap Lifetime*85 - 265VAC Input (300VAC for 5s)*Compact Size*7 year warranty
-
Product
Process Totalizer (analog input)
-
Displays and totalizes 0-1 mA, 4-20 mA, or 0-10 V process signals. Square root extraction is standard for flow applications, allowing display of volume from the 4-20 mA signal of a flow transducer with a linear or squared output.
-
Product
C Series Temperature Input Module
Module
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
