1553 Interfaces
Mil-Std-1553 interfaces.
-
Product
Air Interface Emulator
-
Becker Nachrichtentechnik GmbH
With help of air interface emulators radio field propagations can be emulated reproduceable in laboratory environments. For different applications like cellular, wireless networks or broadcast several types of devices are available.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
Interface RS-232
-
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
Product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
-
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTB
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
Switch Blade
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
PCI 16 Reed Relay Output / 16 Isolated Input Digital Interface (10-30V)
8004H
-
Optimized for sensing up to 24V inputs, the 8004H PCI digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The inputs protect the computer equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. The relays are normally open, and close when energized.
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Single or Dual DDC ACE 1553 Controller
CPCI-1553-DDC-1
Controller
Single or Dual DDC ACE 1553 Controller, Bus Controller, Remote Terminal, Bus Monitor Modes.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
Interface Level Transmitter
Desalter
-
The Drexelbrook Desalter Interface Level Transmitters accurately measure the electrical interface in the emulsion, even in upset conditions.DesalterThe Drexelbrook Desalter interface level transmitter provides an excellent solution for control of vessels that use electrostatic grids to accelerate separation.This reliable level transmitter is specially designed to maximize the throughput of oil/water separators and accurately measures the electrical interface in the emulsion even in upset conditions. This measurement is critical because the separation vessel operates at maximum efficiency when the electrostatic grid is close as possible to the interface.
-
Product
Wireless Sensor Tags & Interfaces
-
NFC and UHF RFID sensor tags offer a highly integrated solution for remote sensor data logging. The tags conform to the specifications of the NFC/ISO15693 as well as the UHF RFID standards. Featuring on-chip temperature sensing and the exclusive cool-Log™ technology, these sensor tags enable innovative and cost-sensitive solutions in food and pharmaceutical cold-chain management, industrial process control, remote monitoring and healthcare applications. NFiC™ ICs from ams lower the barriers to NFC integration in electronic devices thanks to their small footprint, high data rate, flexible data transfer modes, fully passive NFC tag emulation and advanced energy harvesting. NFC/HF interface tags are best suited to demanding consumer and industrial applications such as zero-power device configuration and set-up, feature-rich contactless cards for payment and authentication, smart toys and connected cars.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
-
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
PCI 32 Channel Reed Relay Output Digital Interface
8007
-
The 8007’s PCI digital I/O interface reed relay outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
True Reference Audio Interface With MDIO Expansion
Titan
-
Titan and Atlas are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Titan is ideal for music and sound recording, multi-tracking, overdubbing, stem-based mastering, analogue summing and critical listening applications.
-
Product
5G NR FR1 Module, M.2 3052 B-Key Form Factor, USB Interface
AIW-356
-
Main Chipset Qualcomm SDX62Max DL peak rate 3.2 Gbps NR Sub6 EN-DC, Max UL peak rate of 900MbpsUL Max support 2 MIMO, DL Max support 4 MIMOM.2 3052 form factor, USB interfaceOperating temperature: Normal operating temperature: -30 ~ 75 °C (-22 ~ 167 °F)AIW-356 DQ-N01: 5G NR FR1 module, USB communication interface, with GNSS, for USAIW-356 DQ-E01: 5G NR FR1 module, USB communication interface, with GNSS, for EU, for AustraliaAIW-356 DQ-JK1: 5G NR FR1 module, USB communication interface, with GNSS, for Japan, for South KoreaAIW-356 DQ-C01: 5G NR FR1 module, USB communication interface, with GNSS, for China
-
Product
Double Display TRMS Multimeter with USB Interface
VA42 VA42R VA42RP
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
This instrument complies with IEC 61010-1:2001, CAT II 1000V and CAT III 600V overvoltage standards. See Specifications.
-
Product
Power Interface Board 6U, 2 PSU connectors with AC pins
106PIBM602-9001R
-
The PIB 6U 2 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Multi-Channel, Multi-Protocol ARINC Ethernet Appliance
ENET-MA4
Ethernet Interface
eNet-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNet-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 8 ARINC channels.
-
Product
PMC Carrier for PCI Card Interface
TPCI270
-
The TPCI270 is a standard 33 MHz, 32 bit PCI carrier for a single PMC Card. Itprovides PMC front I/O and PMC P14 rear I/O. This PMC to PCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in standard PCI systems.
-
Product
Interfaces And Control Boards
-
Acts as a bridge between a machine, motor controller, or PLC and related drive amplifier, feedback device and/or software.
-
Product
Peripherals & Interface Cards
-
Interface cards are plug-in modules that provide interfaces for control/communication of/with external components or test items.The modules themselves are controlled via standard interfaces such as USB 2.0/3.0, PCI, PCIe, PXI, PXIe or LAN.
-
Product
Quad Serial FPDP Interface with Virtex-6 FPGA - 3U VPX
Model 52611
-
- Complete serial FPDP solution- Fully compliant with VITA 17.1 specification- Fiber optic or copper serial interfaces- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x4- LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
