ICT Systems
See Also: ICT
-
Product
In-Circuit Testers
-
SPEA’s Bed of Nails Board Testers are scalable In-Circuit Test platforms that deliver the shortest test time, superior diagnostic accuracy, and extended test coverage for the most comprehensive range of electronic products.SPEA’s In-Circuit Board Testers are designed to increase yield, shorten the testing time, and cut the cost-of-test. Thanks to their unique Multi-Tester and Multi-Core Architecture, the SPEA’s Board Testers provide up to ten times greater throughput than conventional ICT test systems.
-
Product
In-circuit Test
i3070
-
The Keysight i3070 In-Circuit Test (ICT) System embodies proven technology, enhancing test efficiency through time-tested software, hardware, and programmability. Catering to diverse PCBA sizes, it addresses applications such as IoT, 5G, automotive, and energy. Its unique design minimizes undesired effects from parasitic capacitance, enhances immunity to crosstalk, and eliminates stray signal coupling, ensuring consistent and repeatable measurements.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
In-Circuit Test System
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Automated ICT System
-
With world-famous in-circuit test technologies and innovations around automated inline handlers, Keysight automated inline ICT solutions are versatile and flexible and provide you:
-
Product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
Controller
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
Product
4-Module ICT System, I307x Series 6
E9903G
In-Circuit Test System
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
System
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
Product
In-Circuit Test Systems For Sale
Test System
Forwessun offers a comprehensive range of global services for a variety of Test Systems. We provide refurbished systems that have undergone rigorous testing, giving you reliable performance at a fraction of the cost of new equipment. Whether you’re looking for a long-term solution to enhance your testing capabilities or a temporary setup to meet increased production demands, we have flexible options to suit your needs. - HP3070- Agilent - Keysight- GenRad- Teradyne Our bespoke rental agreements make it easy to scale up without permanent investment—simply return the system when it’s no longer required. For ongoing support, we offer calibration, repair, and maintenance services through convenient service contracts. If you’re looking to retire any outdated or non-functional In-Circuit Test (ICT) systems, we’ll offer fair market prices, helping you maximise value on any surplus equipment.
-
Product
2-Module ICT System, I317x Series 6
E9902G
In-Circuit Test System
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
Systems Certification
System
Project integration offering a complete turnkey solution including design, engineering, FAA and international regulatory certification services and testing, and installation kit manufacturing.
-
Product
LabVIEW Development Systems
System
Base--The instant productivity of graphical development for DAQ and instrument controlFull--A rich set of routines for mathematics, signal processing, and signal generationProfessional--The solution for professional developers who need code deployment or validationLabVIEW suites--LabVIEW Professional plus industry-specific add-on software
-
Product
LabVIEW Full Development System
System
LabVIEW is engineering software designed specifically for test, measurement, and control applications that require rapid access to hardware and data insights. The LabVIEW Full Development System is recommended to customize your engineering application with advanced inline analysis and control algorithms. For applications that require software engineering tools to develop, debug, and deploy professional applications, consider LabVIEW Professional Development System.
-
Product
Mezzanine System
5158
System
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
AIM System Solutions
System
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
Product
VIP Cabin Management Systems
System
Where elegance meets powerful functions, add a new level of electronic sophistication to your cabin.
-
Product
Mezzanine System Carrier
MMS8010 / MMS8011
System
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
Product
Test Requirements Document (TRD) System
TRD Software
System
The Test Requirements Document (TRD) System helps users develop and document the strategy and structure of test programs.
-
Product
Simulation Systems
System
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
Seat Actuation Systems
System
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
Product
IFC Antennas & Radome Systems
System
System solutions providing inflight internet and live TV connectivity including satellite communications (SATCOM) systems, protective radome enclosures, antenna mounts, bird strike solutions, and adapter plates.
-
Product
Multipurpose Mobile PXI DAQ System
System
The mobile DAQ system achieves seamless integration among signal conditioning, data acquisition, and synchronization that benchtop instruments would not have achieved. By choosing this system over using benchtop instruments, United Technologies Research Center saved hundreds of thousands of dollars.
-
Product
TO-CAN Package Inspection System
7925
System
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
Product
Systems Integration (SIL) Lab Data Acquisition
System
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
Product
Checkpoint Security System
ConneCT
System
The ConneCTTM Checkpoint Security System is an advanced aviation security explosive detection system (EDS) engineered to deliver superior threat detection, dramatically improved passenger throughput, and low total cost of ownership.
-
Product
Radisys Management System
System
The Radisys Management System is a carrier-grade management solution built to scale as your network evolves while maintaining high-performance levels.
-
Product
4U 8-Slot CompactPCI® System with Redundant Power Supplies
cPCIS-6418U
System
The cPCIS-6418U Series Subsystem is designed for maximum density and has 8 horizontal slots for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
Vision Systems
System
Embedded vision systems, also referred to as compact vision systems, offer an alternative to Smart cameras and computer-based systems. The ADLINK EOS series is a complete embedded system that offers image acquisition, processing, archiving, and display capabilities. It is equipped with a multi-core CPU, ideal for applications requiring high computing power and multi-camera imaging, such as 3D vision and robotics guidance. Featuring rich I/O connectivity with factory-floor networks, including RS-232/422/485, USB, and isolated digital I/O, as well as onboard storage, ADLINK’s embedded vision system is ready to deploy. A system monitoring feature, feeding back temperature and voltage data, combines with a watchdog timer to maximize robustness and reliability of the ADLINK EOS series in mission critical applications.
-
Product
Avenir VIP IFE & CMS Systems
System
The new Avenir Line is the next generation of Cabin Management and In-Flight Entertainment Systems (CMS/IFE) from Astronics. Avenir incorporates the latest technologies to deliver native 4K video distribution through the highest bandwidth Ethernet network system in the industry. It also provides a fully customizable experience, which extends to the graphical user interface.
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
