Step Attenuators
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
-
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Step Probes
-
*Precisely controlled probe travel*Step tip geometry*Replaceable and non-replaceable versions*Plating options available
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
-
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
41-182B-003
-
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI Hybrid Amplifier/Attenuator
M9352A
-
The M9352A modules are custom built and tested to nominal* performance characteristics. Full regulatory and safety testing has been performed. This product has the same warranty and support services as other Keysight instruments. Because it is custom built, Keysight recommends checking availability and delivery information before ordering the product.
-
Product
Coaxial Attenuators Set
11583C
-
The Keysight 11583C contains a set of four 8493C attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8493C are APC-3.5 connectors with a maximum frequency of 26.5 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Variable Optical Attenuator Module with Angled Interface
81571A
-
The Keysight 81571A variable optical attenuator features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
Product
SPL-03C-090 Step Probe
SPL-03C-090
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 127Recommended Travel (mm): 3.22Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
Product
Variable Optical Attenuators
-
Fast attenuation speed with low insertion loss and built-in power monitoring. Operates in fixed attenuation or constant output power modes and supports SMF, MMF and PMF.
-
Product
Coaxial Fixed Attenuator, DC to 67 GHz
8490G
-
Keysight's 8490G precision coaxial fixed attenuators maximize your operating frequency range up to 67 GHz by providing industry-leading attenuation accuracy, coupled with low SWR and a variety of attenuation options to suit your application needs. The attenuator is available in attenuations of 3, 6, 10, 20, 30 and 40 dB. The 8490G is swept-frequency tested to ensure it meets specifications at all frequencies.
-
Product
One-Channel Variable Optical Attenuator
N7761A
-
The N7761A attenuator is an extension to Keysight's high density N77xx-family that establishes a new standard in space-saving fiberoptic instrumentation.
-
Product
PXI Switchable-Input Programmable Step Attenuator Module, DC to 50 GHz
M9169E
-
The M9169E is a 3-port PXI programmable step attenuator module with a switchable path for a calibrator signal (cal input) into the input of a signal analyzer to improve amplitude accuracy. The M9169E has 0.03 dB insertion loss repeatability throughout the operating life of up to 5 million cycles per section. Its excellent attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
Attenuators
-
Teledyne RF & Microwave offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, RF&M has a product that meets your demanding needs.
-
Product
Attenuators
-
We feature over 20,000 Microwave & RF Attenuators from 0-67GHz in stock. 1.85mm 67ghz attenuators. SMA attenuators to 3ghz, SMA Attenuators to 6ghz, 18ghz, & 27ghz; Type N attenuators to 6 ghz, 50 watt 3ghz Type N Attenuators, 500 watt 8.5ghz attenuators. Rotary, Variable, & Switch attenuators to 40Ghz. 2.4mm 50ghz attenuators.
-
Product
PXI 10 Channel High Voltage Attenuator
41-660-001
-
The 41-660 and 41-661 are high voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Attenuators
-
CAES offers a full range of RF Attenuators for your designs including analog and digital PIN Diode as well as Switched-bit Attenuators.
-
Product
Attenuators
-
A passive electronic device that reduces the power of an electrical or optical signal without significantly distorting its waveform.
-
Product
Fixed Attenuators
-
ZTS provides 2 to 1000 Watts fixed attenuators with many types of connectors to choose from, maximum frequency would reach 67 GHz, we also provide custom or calibrated service as per your request.
-
Product
Attenuators
-
Optical attenuators reduce the intensity of transmitted light uniformly across the spectrum. Applications include preventing too much light from overloading a receiver.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Calibration Hex Step Adapters
-
When performing torque wrench calibration or testing, adapters are often needed, especially with torque wrenches that have open-end heads. Mountz’s calibration hex step adapter features four common sizes, which will increase the productivity of your torque wrench calibration process. This adapter will make testing and calibration simple and efficient.
-
Product
Attenuators
-
A device consisting of an arrangement of resistors which reduces the strength of a radio or audio signal.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8493B
-
The Keysight 8493B coaxial fixed attenuator provides precision attenuation, flat frequency response, low SWR over broad frequency range at a low price. The attenuator is available in nominal attenuations of 3 dB and 6 dB, also 10 dB increments from 10 dB to 30 dB. This attenuator is swept-frequency tested to ensure it meets specifications at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Step Recovery Diodes
-
SemiGen’s SSR series of Step Recovery Diodes are epitaxial silicon varactors which provide high output power and efficiencies in harmonic generator applications. Using custom epitaxial wafers, our process ensures high reproducibility. The silicon dioxide passivation process assures greater stability and low leakage currents over temperature. Uniform capacitance ensures repeatability from device to device. These diodes are available in chip or packaged form.
-
Product
Step Recovery Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
Product
Optical Variable Attenuator
OVA-50
-
OVA-50 Optical Variable Attenuator can precisely attenuate input optical signals at 1310/1490/1550/1625nm wavelengths and directly output defined stabilized optical signals. OVA-50 is applicable in various testing situations.
-
Product
Attenuator / Switch Driver
11713E
-
The 11713E attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
Attenuators
-
An attenuator is an electronic device that reduces the power of a signal without appreciably distorting its waveform.
-
Product
Step Height, Parallelism and Flushness Finish
stepCHECK
-
8tree's stepCHECK delivers accurate 3D measurement and instant analysis of step height, parallelism, and flushness finish between adjacent surfaces. Using the augmented reality reprojection of results, operators can visualize surface alignment non-conformity and identify corrective actions, right on the shop floor. With stepCHECK, inspection of surface alignment GD&T requirements becomes easier (Geometrical Dimensioning & Tolerancing).
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
