Step Attenuators
-
Product
Source - 20 GHz Source with Amp Attenuator
RI8554A
-
Automated Instruments, Powerful Development Tools and Worldwide Support
-
Product
Voltage Control Attenuator
-
RF Lambda’s voltage control attenuators allow for precision control of RF signals. With a voltage variable control pin the signal can be fine-tuned as needed by the system. These attenuators offer fast response time and wide band operation. Hermetically sealed options are available upon request.
-
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
Product
Optical Attenuators
-
Guilin GLsun Science and Tech Group Co., LTD
Optical Attenuators by GLSN
-
Product
PXI Attenuator
-
Keysight offers step attenuator modules that operate across a broad frequency range of DC to50 GHz.
-
Product
Millimeter-wave and Microwave GaAs Attenuators
-
Keysight Technologies provides MMIC attenuators ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
Attenuators
-
A device consisting of an arrangement of resistors which reduces the strength of a radio or audio signal.
-
Product
Fixed Attenuator (Waveguide)
-
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
Product
Step & Touch & Earth Impedance
-
The kit applyed with STS 5000, STS 4000 or eKAM, allows to perform the following types of test: soil resistivity, ground grid resistance, step and touch tests and overhead lines zero sequence and mutual coupling coefficients
-
Product
Optical Variable Attenuator
TW3303
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Optical Variable Attenuator TW3303 TW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there, thereforeTW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV
-
Product
Flexible Device Support for All Steps of the CPE Lifecycle
Connect Xperience
-
Elevate user experiences and deliver unparalleled service to end users with Connect Xperience. Enable self support capabilities and give users the power to control all connected devices on their premise at their fingertips with open and flexible device support.
-
Product
Fixed Attenuators
-
BroadWave attenuators reduce the strength of an RF signal without appreciable distortion of its waveform.
-
Product
Integrated Two Channel Variable Optical Attenuator with two Optical Power Meter Channels
N7752A
Optical Attenuator
The Keysight N7752A combines an attenuator with 2 front-panel power meter channels, offering exceptional performance at a low price. The power meters permit measurements from any point in the measurements setup and assist in calibrating power offsets with respect to the attenuator output.
-
Product
Programmable RF Attenuators
-
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
-
Product
Digital Attenuators
-
Compact microwave digital step attenuators with low insertion-loss, USB control and power, 60 or 90dB max setting, 0.25 or 0.5dB step size, ranging from 10MHz to 24GHz. Front OLED display and user control buttons standard.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
Attenuator
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Attenuators
-
Teledyne Microwave Solutions (TMS) offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, TMS has a product that meets your demanding needs.
-
Product
Power/Voltage Rail Probe, 2 GHz Bandwidth, 1.2x Attenuation, +/-60V Offset, +/-800mV
RP2060
-
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Variable attenuator
-
Optimum for simulation of wireless communication equipments, such as handover test, dynamic motion test and receiving sensitivity test. Moreover, optimum for the simulation of the receiving trouble by the rainfall attenuation in BS/CS digital broadcasting.
-
Product
Coaxial Dynamics RF Attenuators
-
Coaxial Dynamics RF Attenuators offer a reliable and accurate method for reducing RF power levels. All of our designs dry convection cooled and can be used in any position.
-
Product
Variable Attenuator
VAXE
-
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
Product
Attenuators
-
Keysight Attenuators offer a compact, rugged design with exceptionally low insertion loss. Our latest design evolution sets new standards for size and performance. Keysight Attenuators provide excellent repeatability and safeguard your test platform from failures, downtime, and lost production. Discover which of our Attenuators best suits your test and measurement needs.
-
Product
SPL-03C-114 Step Probe
SPL-03C-114
Step Probe
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 50Test Center (mil): 125Full Travel (mil): 170Full Travel (mm): 4.32Recommended Travel (mil): 127Recommended Travel (mm): 3.23Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
-
Product
CP500X, 500 MHz, ±60 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
784253-01
High Current Probe
The CP500X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 1 meter in length. The CP500X attaches to BNC connections on both the signal input and instrument sides.
-
Product
Digital Step Phase Shifter
-
RF Lambda’s digital step phase shifters are designed to actively change the phase of an RF signal using digital TTL control signals. They are available in a variety of frequencies, phase shift ranges, and step sizes. Hermetically sealed options are available upon request.
-
Product
Attenuators
-
Flann manufactures a portfolio of both manual and programmable attenuators that cover a wide range of applications and waveguide bands
