Step Attenuators
-
Product
SP500X , 500 MHz, ±300 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
783629-01
-
The SP500X, or Multi-Contact Isoprobe IV - 10:1, is a standard passive probe with fixed 10x attenuation for oscilloscopes that provide 1 MΩ input impedance.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
Variable Optical Attenuators
5420
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
Fixed Attenuators
-
BroadWave attenuators reduce the strength of an RF signal without appreciable distortion of its waveform.
-
Product
NI-5191, 800 MHz, ±30 V, 10X Attenuation, Differential Active Oscilloscope Probe
781785-01
-
The NI-5191 is a differential, active voltage probe that offers 800 MHz of input bandwidth with a 10:1 attenuation ratio. You can use it with oscilloscopes that provide 50 Ω input impedance. You can power the probe using a Type-N barrel power connector from a USB port or using a 9 V alkaline battery.
-
Product
SMA Stainless Steel Fixed Attenuator
WK0602-06
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Manual Attenuator (Coaxial)
-
RF Lambda’s manual coaxial attenuators are used to control signal levels using a manual control knob or buttons. These are highly reliable and commonly used in test setups where the operator needs access to tune RF signals without the need for any digital or voltage control.
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
-
Product
SA1500X, 1.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784256-01
-
The SA1500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
Attenuator
J2140A
-
CharacteristicRatingMaximum Input Level+20dBm3dB Frequency RangeDC ~ 50MHzMaximum VSWR1.3Attenuation Accuracy0.2dB
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
-
Product
Digital Attenuator Operating Frequency of 1 to 20 GHz
LDA Series
-
The LDA series of Lab Brick® RF and Microwave Programmable Digital Attenuators includes 50 Ohm and 75 Ohm bidirectional RF step attenuators with calibrated operation up to 20 GHz. These USB powered and controlled units require no additional DC supply voltage. They are easily programmable for fixed attenuation or swept attenuation ramps directly from the included GUI. Lab Brick Digital Attenuator API DLL, Linux drivers and LabVIEW-compatible drivers are also available for custom programming applications.
-
Product
Variable Optical Attenuators
-
Nanning Xionghua Photonics Technology
Variable Optical Attenuator by Xionghua Photonics
-
Product
Voltage Variable Attenuators To 16 GHz
-
Our family of voltage controlled attenuators is non-reflective, with ranges of 32 dB of 64 dB. Pin diodes are used and the frequency range is 0.25-16 GHz. They operate with a control voltage of 0 to +8 VDC and handle +27 dBm maximum input power. These attenuators are bi-directional: either SMA port may be used for an input.
-
Product
Step & Contact Meter
HT2055
-
HT2055 consists in a power unit and a voltmetric unit, necessary for carrying out step and contact voltage measurements in industrial electric installations (TN systems, transformer cabinets) with a rated test current up to 50A.
