CF
Flash technology storage that retains data without a battery.
-
Product
Centrifugal FFF
CF2000
-
The new advanced Postnova CF2000 Series was developed to become the first professional modular Centrifugal FFF system available. It is completely controled by the NovaFFF single software platform which runs the entire system from autosampler to detectors. The CF2000 Centrifugal FFF incorporates the combined proven know-how and the technologies from three decades of leadership in FFF. Due to its unique design, the CF2000 Centrifugal FFF system offers more flexibility, higher robustness and better performance than traditional particle sizer systems. The CF2000 allows high resolution particle separation and sizing at the same time and consequently sets a complete new standard and offers a real alternative to traditional particle characterization techniques.
-
Product
AC/DC Power Supply 20 W
CFM21M050-S
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 5 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety and is class II | screw terminals
-
Product
Modular TDM / IP Split Mount Radio System
CFIP PhoeniX M
-
CFIP PhoeniX M split mount system consists of PhoeniX M IDU and PhoeniX ODU (XPIC functionality supported). PhoeniX M IDU provides up to 63E1 and 2xSTM-1 bringing the total maximum capacity to 348 Mbps full duplex.
-
Product
Carton Force Analyser
CFA
-
By measuring the stiffness of the substrate and crease bending resistance the user can optimise cartons for faster running and packaging speeds. The instrument allows individual creases to be analysed identifying problem areas in packaging design or manufacture. Industry research indicates that the packaging speeds of pre-glued skillets is governed by the energy required to open creases. The Hanatek CFA is the first instrument to isolate and accurately measure this key parameter The instrument measures: Bending resistance, bending moment, board stiffness, crease recovery stiffness, crease folding force, crease opening force.
-
Product
AC/DC Power Supply 20 W
CFM21S090-T
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 9 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety | JST connector
-
Product
Pre- Locator
CFL PL2+
-
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
Product
Exhaust Fan
CF-400-X
-
This UL approved exhaust fan is typically installed in cabinet top panels, but has many applications. This fan requires a 10” diameter area and extends approximately 4” inside the panel.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
Motherboard
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
-
Product
AC/DC Power Supply 20 W
CFM21M150-E
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 15 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety and is class II | enclosed version
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
Tubeaxial Fan
CF-35
-
This tubeaxial fan is only 3-1/8” square x 1.64” deep, making it ideal for flushing small instrument cases or cooling “hot spots” in large assemblies with a minimal loss of space.
-
Product
Pin Pointer
CFL PP3+
-
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
Product
DC/DC Converter 600 W
CFB600W-110S48P
-
DC/DC converter with 600 W from Cincon | input ranges 43 - 160 VDC | output 48 V | operates in temperature from -40 to +100 °C | according to EN45545-2 fire and smoke | positive control logic
-
Product
Crossed-Field Amplifiers
CFAs
-
Communications & Power Industries
CPI BMD’s crossed-field amplifiers (CFAs) are broadband, phase-stable microwave amplifiers used in coherent radar chains to efficiently generate very high peak output powers from relatively low input voltages which can be either applied to the cathode or an electrode similar to a TWTs cathode or grid pulsing, and in relatively small, lightweight packages. These characteristics make CFAs particularly well-suited for applications in which the transmitter must be either airborne, transportable, mobile or portable.
-
Product
4 Digit Field Indicator
CFIA-40 4
-
1. Using LED to display, and able to be used in dark environment2. No external power needed3. Able to display measured value like pressure , temperature and depth etc4. Display solution 1/99995. Isolated alarm open drain output6. Voltage drop will below 4 volt
-
Product
AC and DC Power Sources
CFS100 Series
-
The CFS100 Series programmable AC or DC output power sources are cost effective source of power for development, test and production applications requiring anywhere from 800VA or less to 4000VA of single phase AC or DC output.
-
Product
Pre- Locator
CFL PL4+
-
The new generation CFL PL4+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 256 km.
-
Product
Pre- Locator
CFL PL4
-
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ Desktop Processor
AmITX-CF-G
Motherboard
Targeted at gaming customers and system integrators, AmITX-CF-G is a Mini-ITX board specially designed for Gaming. AmITX-CF-G features GLI compliance, easy and flexible configuration, security enhancements, and system resilience. The values of AmITX-CF-G include amplified visual impact, guaranteed system integrity, secure transactions with fast TTM and low TCO, and maximized system uptime. AmITX-CF-G can satisfy application function requirements and meet GLI certification which cannot be offered by other conventional Mini-ITX boards.
-
Product
Outdoor Radio System
CFIP-106/108
-
CFIP-106/108 is primarily designed for IP networks and provides Fast Ethernet interface with capacities from 8 Mbps up to full duplex 100 Mbps Fast Ethernet. In addition to that, CFIP-108 has a 4xE1 port for legacy equipment connectivity and for use in hybrid TDM/IP networks.
-
Product
CAMAC-to-FERA Bridge
CFB
-
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
Product
AC/DC Power Supply 25 W
CFM25S360-T
-
AC/DC power supply with 25 W from Cincon | input ranges 90 - 264 VAC | output 36 V | operates in temperature from -30 to +70 °C | class II | wafer version
