Sensor Amplifiers
-
product
P-Series Wideband Power Sensors
The Keysight P-Series wideband power sensors provides peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power and statistical data of wideband signals.
-
product
Fully Differential Amplifiers
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
product
Lambda Oxygen Sensor
KS60002
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Sensor Processing
If you need analog input boards for video compression, SDR, SIGINT, radar, sonar, imaging or T&M - we can help.
-
product
Collision avoidance radar sensor
OndoSense reach WA (E)
With its wide detection range, the OndoSense reach WA (Wide Angle) is particularly suited for detecting obstacles such as vehicles, people or objects as well as for positioning robots and machines. It detects static and moving objects even at close range from 0.1 meters and can be easily integrated even in confined spaces, thanks to its very small design. With up to 4 adjustable sensor zones, the OndoSense reach WA is ideal for flexible monitoring of security areas or collision avoidance of mobile robots or other vehicles. Thanks to innovative radar technology, the radar sensor always reliably detects objects of any nature, even outdoors or in difficult environments with dirt, smoke, steam, rain or poor lighting conditions. And as a result of its high measuring rate of 200 Hz, it always reliably detects obstacles even with fast movements.
-
product
TMR Linear Displacement Sensors
MultiDimension Technology Co.,Ltd.
A magnetoresistive technique based non-contact linear position sensor, with enhanced accuracy, fast frequency response and anti-electromagnetic interference feature.
-
product
Sensors
Campbell Scientific sensors measure a broad array of parameters for environmental, water resource, research, and industrial applications. The sensors output electrical signals, which are transmitted to data loggers. In addition to our extensive line of sensors, almost any commercially available sensor can be measured by our data acquisition systems.
-
product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
product
Remote Temperature Sensor
CHV-RTS
The CHV-RTS is a wall-mounted remote temperature sensor designed for use with select Crestron thermostats. The 1-1/2 inch diameter face of the CHV-RTS protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
-
product
HF Low Noise Amplifier
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
product
Electrocardiogram Logger Sensor
NUL-218
Identical in its use to a regular medical ECG (electrocardiogram), this is a rather simple three lead based logger sensor. It presents a heartbeat graph that allows a thorough examination of the heart's electrical activity from three different angles. Unlike most ECG devices, this unit operates with non-disposable electrodes.
-
product
Web Sensor with PoE
T3611-2
Ambient temperature, relative humidity t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
product
Oxygen Sensor
KS60006
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Magnetic Field Logger Sensor
NUL-214
This is a very sensitive magnetic fields sensor. It can measure a very low level of magnetic fields such as the magnetic field of Earth.The logger sensor measures the magnetic fields in milli Tesla (mT).
-
product
Temperature Measurement IR Sensors & Detectors
1SC Compensated
A thin film-based single channel thermopile detector that offers thermal compensation to minimize effects of sudden ambient temperature change during the initial five seconds of change. The 1SC Compensated comes in a TO-5 package with a medium sized 1.0 x 1.0mm active area. Compensation is achieved through the integration of two additional half-sized thermopile elements. Internal aperture is standard and precisely defines active area for applications with FOV and/or spot size requirements.
-
product
Belt Alignment Sensors And Misalignment Switches
Electro-sensors belt alignment sensors are mounted along the conveyor belt that needs to be monitored for misalignment. The rub block assemblies are mounted so that the brass surface area is in-line with the edge of the conveyor belt. When the belt wanders it then rubs up against the brass block. The contact with the belt creates friction and heat that the sensor in the brass block records as a rise in temperature.
-
product
Isolated Hall Effect Current Sensors
Isolated Hall Effect current sensors provide accurate high bandwidth current sensing. Vektrex offers models to 320A. For use, the 50-ohm voltage output is connected directly to an oscilloscope or data acquisition system. VCS sensors are magnetically isolated like clamp-on oscilloscope probes. With secure cable attachment, repeatability is ensured.
-
product
Isolation Amplifiers
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
product
Pulsed ESR/EPR: Pulsed Injection-locked IMPATT Amplifiers
Insight Product Company offers pulse injection-locked IMPATT amplifiers for pulse ESR/EPR experiments. Pulsed injection-locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate the amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
product
Differential Magnetoresistive Sensors
ChenYang Technologies GmbH & Co. KG
*Sensing over wide rotation speed range*Robust metallic housing*Signal amplitude is speed independent*Biasing magnet built-in*Best suited for harsh environments
-
product
RF Amplifier
SA1001H
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
product
Compact Sensors
OPTITEMP smart compact sensors for temperature measurement in gases and liquids, in pipes and tanks at medium pressure and flow
-
product
Sensors for C-slot Cylinders
Reliable, high-performance, rugged - magnetic cylinder sensors from SICK for the C-slotMagnetic cylinder sensors from SICK ofter the perfect option for all conventional pneumatic actuators with C-slots. They are precisely tailored for different slot forms.
-
product
Nitrate Logger Sensor
NUL-241
The NeuLog nitrate sensor can be used to measure the concentration of nitrate ions (NO3-) in aqueous samples.Nitrates are used in fertilizers and can contaminate water. Also, untreated human sewage can be a source of nitrate contamination.Nitrate measurements can also be very relevant to study the nitrogen cycle in general and to relate this cycle to plants and algae.
-
product
Electrostatic Sensors
Panasonic Industrial Devices Sales Company of America
With easy data management, Panasonic Electrostatic Sensors can assist to identify and diagnose problems caused by static electricity. In real time, these Sensors can determine ionizer status and identify ionizer damage. With a measurement range up to +/-2 kV and suitable for severe conditions, these Sensors can be used for measurements such as surface potential, frictional electrification and lead frame charge removal.
-
product
Single Channel High Voltage Linear Amplifier
F20A
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Low Noise Amplifier
Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
product
MOSFETs For Amplifier
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
product
Low Noise Amplifiers
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
