IR Sensor
Detect infrared radiation and produce a measurable signal of the detected amount.
-
Product
Two-Path Diode Power Sensors
NRP-Z2x1
Power Sensor
The R&S®NRP-Z211 two-path diode power sensors combine all key characteristics relevant for their use in production: They are cost-effective, fast, precise and USB-capable. The sensors support the same measurement functions as the R&S®NRPxx‑Z11/R&S®NRP‑Z2x/R&S®NRP‑Z31 three-path diode power sensors and offer the best price/performance ratio in their class.
-
Product
USB Power Sensor, 50 MHz to 24 GHz
U2002A
Power Sensor
Fast and simple setup with plug-and-play USB connectivity. Eliminates the need for a separate power meter.
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
LED Sensor
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
LED Sensor
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
Product
E-Series Average Power Sensor
E9300A
Power Sensor
The E9300A diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -60 to +20 dBm (80 dB dynamic range).
-
Product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
Power Sensor
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
Product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
Power Sensor
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
Product
Thermocouple Power Sensors
N8481B
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
10 MHz to 18 GHz LAN Wide Dynamic Range Average Power Sensor
L2052XA
Power Sensor
The Keysight L2052XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz LAN average power sensor.
-
Product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
DC/10 MHz – 18 GHz USB Thermocouple Power Sensor
U8481A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor
-
Product
10 MHz To 54 GHz USB Wide Dynamic Range Average Power Sensor
U2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis
-
Product
10 MHz to 53 GHz LAN Thermal Vacuum Compliance Power Sensor
L2065XT
Power Sensor
The Keysight L2065XT is a fast, accurate and wide dynamic range 10 MHz – 53 GHz LAN thermal vacuum compliance power sensor.
-
Product
10 MHz To 54 GHz LAN Wide Dynamic Range Average Power Sensor
L2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
E-Series Average Power Sensor
E9301H
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -50 dBm to +30 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formatsLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
3U cPCI Sensor Interface Unit
SIU31
Sensor Interface Unit
NAI's SIU31 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU31 uses one NAI field-proven, 3U cPCI board to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
10 MHz to 40 GHz LAN Wide Dynamic Range Average Power Sensor
L2054XA
Power Sensor
The Keysight L2054XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN average power sensor.
-
Product
S2 Penta High-Sensitivity Sensors
ULP S2 PCI/V HS
LED Sensor
The Universal LightProbe S2 Penta High Sensitivity Sensor features the same popular built-in color binning as the regular S2 Penta Sensor, and is designed test extremely dim LEDs, providing an analog output for intensity, ranging from 0 to 4 volts, corresponding to the LED’s luminous intensity in millicandelas. Implemented in a unique and customizable 2-Part solution, the S2 Penta High Sensitivity Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: <1.2s color & intensity outputs simultaneously (the brighter the LED, the shorter theresponse time)Fiber-Optic Probes: Wide Aperture Fiber-Optic Probe recommended
-
Product
Thermocouple Power Sensors
N8487A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
10 MHz – 6 GHz USB Power Sensor
U2001A
Power Sensor
U2001A USB power sensor enable fast, simple setup by providing plug-and-play USB connectivity and by eliminating the need for a separate power meter.
-
Product
Astrosystems Position Sensors
HST-21U Transducer and Encoder
Position Sensor
NAI offers resolver-based Astrosystems Absolute Position Sensors for the packaging, material handling, and automated manufacturing industries. Specifically designed for rugged defense and industrial applications, these highly accurate and programmable units feature standard interfaces and rugged designs. They simplify machine set-up, reduce overall costs, extend product life, and provide a very high level of application flexibility.
-
Product
IR Detectors
-
Opto Diode manufactures high performance infrared detectors with a wide variety of active area sizes, cooling alternatives, packaging, windows, lenses, and filters options. These detectors are ideal for gas analysis, emissions monitoring, spectroscopy, process control, flame and fire monitoring. Our A Series lead sulfide (PbS) detectors provide the highest sensitivity in the 1µm to 3µm wavelength region. Our B Series lead selenide (PbSe) detectors deliver the best overall performance in a wider spectral range from 1µm to 5µm. Our multichannel (MCDs) devices are ideal for simultaneous detection of multiple gases including CO2, CO, and other hydrocarbons.
-
Product
Thermocouple Power Sensors
N8485A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
IR Detectors
-
IR detectors have been a part of our standard product range at LASER COMPONENTS for almost three decades. A distinction is made between sensors for the near infrared range (NIR) from 1.0 µm to 2.5 µm and those for the mid-infrared range (MIR) above 2.5 µm. IR detectors of all modes of operation are a part of our product portfolio and leave nothing to be desired.
-
Product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
-
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detection in explosive locations. Because the FLIR A310 ex is rated IP 67, it can be installed in dusty environments. The Flame-Proof Enclosure "d"prevents any explosion transmission from the inside of the enclosure to the outside.
-
Product
Pocket IR Radiometer
IR-940
-
Shenzhen Chuangxin Instruments Co., Ltd.
Pocket IR Radiometer is a handheld radiometer with the characters of high-precision, pocket, stable property and easy operation.
-
Product
-AC/DC/IR Hipot Tester
Sentry 30 Plus
-
Wuhan Fanke Transformer Manufacture Co., LTD
Sentry 30 Plus - AC/DC/IR Hipot Tester
-
Product
Dynamic IR Scene Projectors
Mirage™
-
In 1999, SBIR introduced MIRAGE™, the world’s first integrated Dynamic IR Scene Projection System, designed to support hardware-in-the-loop testing of missile seekers, FLIRs, counter measure simulation and tracking systems. MIRAGE™ is a complete turnkey infrared scene projector that utilizes unique resistive emitter array technology to produce high definition dynamic IR scenes. The original MIRAGE™-1 used a 512 x 511 pixel resistive array emitter capable of frame rates up to 200 Hz. Below is a list outlining the progression of the product line and a list of SBIR’s currently available scene generation systems:
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
Product
IR Targeting Sights
-
L3 Cincinnati Electronics’ NightConqueror high-performance thermal imagers have been selected as the imager of choice for new platforms and as an upgrade to many existing legacy vehicles for U.S. and foreign militaries. These modules carve out a true path to horizontal technology insertion across numerous battle platforms. They are true "drop-in replacements" that in every way meet or exceed the older unit's form, fit and function. L3 Cincinnati Electronics' upgraded legacy platforms provide flexibility and synergy in a variety of applications, addressing many of today’s most difficult mission profiles.
