Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Analog Distribution Amplifier
DA 1:54
-
The DA 1:54 Analog Distribution Amplifier is designed to make it simple to distribute analog signals generated by Spectrum products to multiple locations and to overcome long cable runs. The DA 1:54 consists of three separate amplifier sections that are factory- configured to operate independently or ganged together, depending upon requirements.
-
Product
DSP Dual Phase Lock-In Amplifier
SR850
-
Stanford Research Systems, Inc.
The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers?higher dynamic reserve, lower drift, lower distortion, and dramatically higher phase resolution.
-
Product
4-Axis Pulse Motion Controller
AMP-104C
-
The AMP-104C is a cost-effective 4-axis motion controller card with a PCI Express® interface that can generate a pulse train up to 4.9MHz to control a motor. With more general purpose IOs and 4-channel encoder feedback input, the AMP-104C can be used for a multitude of scenarios or applications. As a motion controller, the AMP-104C provides non-symmetric acceleration and deceleration speed profile settings, T-curve and S-curve speed profile control, and selection of motion stop method.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
SparkFun Pulse Oximeter And Heart Rate Sensor
MAX30101 & MAX32664 (Qwiic)
-
The SparkFun Pulse Oximeter and Heart Rate Sensor is an I2C based biometric sensor, utilizing two chips from Maxim Integrated: the MAX32664 Biometric Sensor Hub and the MAX30101 Pulse Oximetry and Heart Rate Module. While the latter does all the sensing, the former is an incredibly small and fast Cortex M4 processor that handles all of the algorithmic calculations, digital filtering, pressure/position compensation, advanced R-wave detection, and automatic gain control. We've provided a Qwiic connector to easily connect to the I2C data lines but you will also need to connect to two additional lines. This board is very small, measuring at 1in x 0.5in (25.4mm x 12.7mm), which means it will fit nicely on your finger without all the bulk.
-
Product
Optic Node With Amplifier
OX 755
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes cum Amplifier- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
30A, 50 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP030B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Standard Signal Isolating Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
Product
Wideband Pulse Profiling Sensors
-
LadyBug wideband Power Sensors feed power waveform samples into high speed A/D converters. The measured power is processed and then delivered as required by the user. These sensors are capable of delivering everything from basic power, to time domain scope-like profiles of the modulated waveform, such as the pulse shown at right. Multiple time gated measurements, crest factor, pulse power, and statistical measurements are all possible with these sensors.
-
Product
High Performance Function/Arbitrary/Pulse Generator 25MHz Or 50MHz, 1 Or 2 Channels
TG251xA/501xA Series
-
One or two channels0.001mHz to 50MHz/25MHz range; 14 digits or 1uHz resolution.Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic and PRBS.True pulse generator with variable delay and variable rise/fall.Arbitrary waveforms of up to 128K points at up to 125MS/s.Waveform storage using USB flash drives.Large graphic LCD with simultaneous text and waveform display.Comprehensive internal and external digital modulations including AM, FM, PM, PWM, FSK, BSPK, Sum and PRBS.20mV to 20V pk-pk output from 50Ohms ; plus multi function aux. out.Storage for multiple instrument set-ups in non-volatile memory.Waveform Manager Plus for Windows software included.Programmable via USB and LAN (LXI) interfaces; GPIB optional
-
Product
Femtosecond Optical Parametric Amplifier
CDP 2017
-
*> 30% conversion efficiency from pump pulse to parametric radiation*Wavelength conversion for ExciPro, TAPPIR, FOG 100-DA*Wavelength conversion options for wavelength tuning from 240 nm to 16 mm
-
Product
Split type Pulse Current Sensor
PCT-06
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
Medium-Power, Broadband Amplifiers
-
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
Ka-band Power Amplifier (33-37 GHz, 10 Watt Output Power)
-
*Frequency band, GHz: 33-37 *Output power, typical, W: 10 (40 dBm) *Gain, dB, typical: 30*Gain flatness: 2 dB Max *Pulse width, Max.: 100 nanoseconds - 60 microseconds *Pulse reptition frequency: up to 100 KHz *Oprating temparture: -40 deg. Celsius to 60 deg. Celsius *Dimensions: 245 mm x 124 mm x 30 mm
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Low Noise Amplifier
DLNA8-0.1-18G-2223
-
Low Noise Amplifier, Frequency 1~18GHz, Gain 24dB, Noise figure 3.2dB, P-1dB 22dBm, SMA Female
-
Product
Reference DAC, Pre And Headphone Amplifier
CALLIA
-
Designed and manufactured in the United Kingdom, CALLIA embodies the Prism Sound uncompromising approach to audio resulting in the most accurate and detailed DAC available.
-
Product
Single Channel High Voltage Linear Amplifier
F20A
-
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Galvanic Isolation Amplifier
X005 Series
-
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
Product
Pulsed Fiber Amplifier
MOPA
-
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
Product
SX Range Broadband Power Amplifiers 0.8 GHZ - 6 GHZ
SX Series
-
Solid-state amplifier / Class A. Broadband (Dual-band): 0.8 GHz - 6 GHz. Typical output power:
-
Product
Pulse Limiter
KH43101
-
Beijing KeHuan Century EMC Technology Co,.LTD
1, frequency range 9KHZ~30MHZ 2, in-band loss 10dB+-1db 3, VSWR <1.25 4, allowable power <1 W 5, input impedance 50Ω (N type)
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Power Amplifiers (MCPA)
-
*Multi-Carrier Power Amplifier supplies an additional 12.9 dB of Gain at high power*Supports iDEN in the 850MHz Band, available for GSM in cellular and PCS configuration*High power handling with low IM and insertion loss*Ideal for combining multiple BTS to a single feeder line and providing increased power to the antenna
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
