Leeb Hardness Testers
See Also: Hardness Testers, Brinell Hardness Testers, Rockwell Hardness Testers, Vickers Hardness Testers
-
product
Downloading Multifunction Tester
ET4500
The new ET4500 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
can be used to carry out 3 wire earth testing and has on board memory to store and download all installation test results for documentation.
Everything about the new ET Series has been designed to save time and make testing easier.Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .Supplied with a full range of accessories.
-
product
Earth Resistance Tester
G-TEST
To check the condition of a grounding connection, an earthresistance tester is used to measure the residual ground voltage,resistance and resistivity (Wenner method).
-
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
Bench Hardness Testers
A classic hardness tester which is measuring the hardness by standard method of Brinell or Rockwell or Vickery or Shor and so on.
-
product
Phase Noise Analyzer and VCO Tester
FSWP
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
product
Distribution Transformer Tester
DOC-2000™
The DOC-2000™ is a test instrument designed for distribution networks transformers up to 167KVA. It can determine the presence of short circuits or an open circuit in the distribution transformer primary winding & also short circuits on the secondary winding. The DOC-2000™ is designed to be operated from an arial device or from the ground at the end of a hot stick without disconnecting the transformer’s secondary windings.
-
product
Hall Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
product
Downloadable PAT Testers
Whether you are PAT testing in house on a regular basis or an electrical contractor testing 1000's of items a week, we have a downloadable PAT tester to suit your testing requirements.
-
product
60204 Safety Testers
For testing the electrical safety of machines and devices according to the machinery directive EN60204 and VDE113.
-
product
Scratch/Shear Tester
3025
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
-
product
Force Distance Tester
925
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
product
5kv 10kv Withstanding Voltage Tester
2671c
Shenzhen Chuangxin Instruments Co., Ltd.
10KV withstand voltage tester High voltage tester, Hipot Tester fast shipping high quality
-
product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
product
Computer Safe Circuit Tester
24550
Safe for automotive computers. Won’t damage sensitive electronic components. Draws less than 21 mA. at 12 volts DC. Operating range 3-28 volts. The red light indicates positive polarity, green indicates negative polarity.
-
product
Mud Cake Friction Coefficient Tester
NZ-3A
Zhengzhou Nanbei Instrument Equipment Co. Ltd
With the development of drilling technology, special technology wells, directional wells, cluster wells do more and more. Lubricating performance requirements of the drilling fluid is also increasing, the processing agent for drilling fluid lubricant is also increasing year by year. Differences in the quality of the lubricant, together with a reasonable need for compatibility, we need an instrument to evaluate.
-
product
Cupping Tester
PCE-CPT 20
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
product
Hipot Tester
STM/L
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
product
Single Phase Socket Tester
K-280
TESCO Knopp’s K-280 Single Phase Socket Tester is designed to detect short circuits, backfeed and wiring errors in a 120/240 volt, 3-wire, single phase self-contained meter socket.
-
product
Portable Appliance Tester
PAT-2E
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Confi guration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (PAT) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplifi ed set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
product
Insulation Resistance Testers
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
product
Automatic Winding Turns Tester
This tester has the advantage of high accuracy and efficiency, limited influence due to the form and size of the coil to be analyzed, and fast & easy operation thanks to the precision sensor and microprocessor that adopt the patent know-how developed by the manufacture. This tester, when in operation, does not need any further adjustment and calibration. Just connecting the clip leads to each terminal lug of the coil winding, then the tester instantly shows the exact number of the winding turns on the digital display. Unlike other similar devices, input the data of standard coil to test against is unnecessary. In this way, this tester greatly upgrades the inspection and analyzing efficiency.
-
product
Battery Tester
700-110
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
*Big LCD display for easy reading.*One 1.55V silver oxide cell battery can last about 24 months.*Auto power off*Test batteries of full size:C,AA,AAA D,N
-
product
Elasticity, Bend & Impact Testers
The performance of coatings when influenced by external stresses caused by stretching, bending or impact, determines their suitability for their designed application. A coating designed for use in the coil coating industry, for example, should have the ability to stretch as the substrate is formed into its desired shape without damage.
-
product
Cable Locator / Tester Kit
5001 TK
Standard Electric Works Co., Ltd
5001 TK is a cable locator / tester kit which provides the testing needs for cable locating and network cable testing.
-
product
Microhardness Testers
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a range of microhardness testing solutions including the cost-effective MT91 and MS-ZH microhardness testing system.
-
product
Partial Discharge Tester
GTPD-2C
GTPD-2C Digital partial discharge tester is the digital partial discharge measuring and analyzer adopting the complete new generation technology. It is suitable for partial discharge detection in manufacturing factory and field handover test of transformers, generators, CT/PT, bushings, GIS, capacitors, power cables, switches and other high-voltage electrical equipment with various voltage levels and capacities.
-
product
Fiber Optical Cable Testers
Encompasses the processes, tools, and standards used to test fiber optic components, fiber links, and deployed fiber networks.
-
product
Aging and Optical Attenuation Tester
LS822
• Build-in DC Power Supply: Forward current preset: 0.1-800mA (special order) Range of forward voltage: 0.1-20.00V • Range of luminous intensity: 1mcd-3,000cd • Range of luminous flux: 1mlm-9,999,000lm(depends on the size of sphere) • Accuracy of photometer: class1; accuracy of electricity: class0.5 • Aging time: 9999Hours 59Munites 59Seconds • Tolerance of time: ±1S/10H • Record time: 16000times • Hold data automatically when the power is off and continue to work automatically when the power is turned on.
-
product
Cable Testers
CableJoG 64
CableJoG 64 can test up to 64 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in the cable testers memory to produce a pass/fail indication of each pin connection.
