Salt Spray Chambers
splash a condensed salt water solution on surfaces testing their corrosion resistance.
See Also: Salt Spray, Chambers
-
Product
Humidity Chambers
-
Used to simulate humidity conditions and their effects on the product or material in question.
-
Product
Condensation Chamber
-
Wewon Environmental Chambers Co, Ltd.
The condensation test chamber does not need special installation conditions, just need to connect to the ordinary power supply and running water can be used normally. The functional diversity of the equipment, fast and low operating costs make the machine a very high cost performance condensation testing machine in the market. The machine can be programmed to control three different test effects: Humidification, natural cooling and drying, and the corresponding temperature and running time of each test, and set the total time of program running and the number of cycles. The condensation tester has an automatic water replenishing device. When the water temperature exceeds the upper limit, there will be a protection device for safety warning, and it is very safe to use.https://www.wewontech.com/condensation-chamber/
-
Product
Ozone Test Chamber
EKT-2001OZ-HPSSX
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
TSA Thermal Shock Chambers
-
Traditional three-zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air is pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
Product
Rain Test Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Rain test chambers for ingress protection testing simulates rain/water test as per IEC 60529 and DIN 40050-9((IP Code standard)) test standard. • IPX1 Protection against vertically dripping water• IPX2 Dripping water ± 15° from vertical• IPX3 Protection against spraying water• IPX4 Protection against splashing water• IPX5 Protection against low pressure jetting water• IPX6 Protection against high pressure jetting water• IPX7 Protection against temporary immersion• IPX8 Protection against continuous immersion• IPX9K Extremely high pressure jetting water
-
Product
Stability Chambers
PH Series
-
The Darwin Chambers PH Series Stability Chambers are designed for performance specifications exceeding FDA and ICH requirements. For GMP studies, ultrasonic humidification provides excellent humidity control and avoids hot spots during mapping. Thermoelectric cooling provides more stable temperature control than equivalent refrigeration systems. All PH series chambers incorporate inherent cooling redundancy, quiet operation, simple serviceability and excellent reliability.
-
Product
Qualmark's HALT Chambers
-
Specialized machines that combine rapid, extreme temperature changes with multi-axis, repetitive shock/vibration to find product design flaws and weaknesses in hours.
-
Product
Automated Corrosion Test Chamber
-
Thermotron's Automated Corrosion Test chambers combine the capabilities of a temperature-humidity test chamber and a salt-spray cabinet. Corrosion chambers eliminate the need to manually transfer products from one environment to another.
-
Product
Near-field Chambers
-
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
Product
UV Test Chambers
-
Labodam provides an excellent range of UV test chambers operating at a variety of UV wavelengths to simulate different light conditions.
-
Product
Xenon Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Xenon test chamber is affordable, full-featured, and has a large specimen capacity. It provides precise control of critical test parameters including spectrum, irradiance, relative humidity, chamber temperature and black standard temperature. Xenon test chamber is used for the selection of new materials, the improvement of existing materials or evaluating the changes in product formulation that affect product durability. This is an ideal instrument for total accelerated light stability and weathering testing.
-
Product
Environmental Test Chambers / Rooms
-
Is an enclosure used to test the effects of specified environmental conditions on biological items, industrial products, materials, and electronic devices and components.
-
Product
Solar Panel Testing Chamber
ZPH Series
-
CSZ's solar panel testing chambers aid in qualifying that modules can withstand the thermal stress caused by repeated changes in high and low temperatures along with exposure to high humidity. Unique air flow design and distribution ensures precise air flow required for solar panel testing.
-
Product
Reach-In Temperature Test Chambers
-
Tenney Environmental designs and manufactures reach-in temperature test chambers in a range of sizes and configurations. Tenney's line of climatic reach-in test chambers can accommodate a variety of products and testing applications. They are available with temperature only and temperature and humidity capabilities. Tenney also offers several optional features that can be selected to enhance their temperature or temperature and humidity chambers.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
-
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Temperature Humidity Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Soluble Salt Profiler
130 SSP
-
The Elcometer 130 Soluble Salt Profiler provides fast and accurate measurement of the level and density of soluble salts - over 4 times faster than other Bresle equivalent methods. The new Elcometer 130 Soluble Salt Profiler allows you to complete a Bresle equivalent test in just over two minutes. The multi-point conductivity sensors enable the Elcometer 130 SSP to accurately display salt concentration, showing exactly where the contamination lies and generating full colour salt density maps in 2D or 3D.
-
Product
Tensile Test Chamber
-
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
Product
Spray Fluxer Pattern Uniformity
Fluxometer
-
Improve Process Quality - Eliminate guesswork when it comes to managing the consistency of flux application during wave soldering. Ordered in the same width as your WaveRIDER pallet, the Fluxometer rides the finger conveyor through the fluxing stage, conveniently and accurately rendering proof of a tuned spray fluxer. So easy to use, operators can perform diagnostic checks in minutes.
-
Product
Environmental Chamber/Stability Chamber - One Door Model
HC20
-
This is a Environmental test chamber/ Stability chamber/Laboratory incubator single door model capable of performing in wide temperature range(0°c to 70°c) with precise temperature control over the entire range.
-
Product
Thermal Shock Chambers
-
Specialized environmental test devices that rapidly move products between extreme hot and cold temperatures to simulate real-world stress.
-
Product
Compact Environmental Chambers
MicroClimate 3
-
The MicroClimate 3 is a compact environmental chamber designed to simulate a full range of temperature and/or humidity conditions. The small footprint of the MicroClimate 3 combined with temperature and humidity capabilities make this chamber the number one choice for testing small components and products. Whether you need to perform temperature cycling tests or expose your product to steady state temperature environments, these chambers will maintain precise and accurate temperature/humidity control throughout your test.
-
Product
Reach-In Temperature and Humidity Control Chamber
-
The High Low Humidity and Temperature Test Chamber from Weiber are specially designed equipments that are used for testing a wide variety of products for their performance under alternating hot and cold temperature and humidity conditions. These test chambers are most commonly employed for the testing of electronic items, electrical devices and equipments, aviation products and other materials and find widespread usage in aerospace industries, electronics industry and scientific organizations involved in material research and development. These climatic test chambers use advanced technologies for highly reliable and accurate test results and are designed for energy efficient, economical and long lasting performance.
-
Product
Halt Hass Chambers
-
HALT and HASS chambers from WEIBER provide extreme temperature & vibration capabilities used during the product design and manufacturing cycles to compress the time normally required to identify design and process weaknesses. HALT techniques are important in uncovering many of the weak links inherent to the design and fabrication process of a new product. HASS techniques are incorporated during the production phase to find manufacturing process defects that could cause product failures in the field.
-
Product
Walk-In Aging Chamber
-
Aging Chamber has been designed to simulate environmental condition to test the stability and reliability of products under stressed environment. Weiber is a leading manufacturer and supplier of Aging Test Chamber in India and abroad. Weiber offers scientific equipments at the most economical rates and versatile design. Microprocessor based Aging Test Chambers are made in accordance with the international testing standards. The equipments are NABL, NSF certified and CE approved. Aging Chamber maintains 25% to 95 % RH. The Test Chamber is digitally controlled delivering accurate result under controlled environmental conditions.
-
Product
Climate Chamber
ICH
-
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
Product
Reach-In Stability Chambers
-
The PH series chambers are designed for performance specifications exceeding FDA and ICH requirements.
-
Product
Chamber Light
LED-CL
-
The Teledyne Bowtech LED-CL Chamber Light is extremely safe and reliable, due to its advanced technology and innovation.The light has 100,000 hour life and has been designed specifically for use within the Hyperbaric Diving environment, whether that is in Hyperbaric Chambers, TUP's, Diving Bells or even Wet Bells.
-
Product
Liquid-To-Liquid Thermal Shock Chambers
-
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles.
