PCMCIA Interfaces
-
Product
LTE Cat4+GNSS, Full-Size Mini-PCIe Form Factor, USB Communication Interface
AIW-344
-
Main Chipset Qualcomm MDM9X072 LTE Antenna Coaxial Connectors +1 GPS antenna connectorLTE FDD:150Mbps DL/50Mbps UL (Cat 4)LTE TDD:130Mbps DL/30.5Mbps UL (Cat 4)Operation: Normal: -30°C ~ +75°C/Extended: -40°C ~ +85°CAIW-344FQ-E02 LTE/HSPA+/GPRS module, with GPS, for EU, for TW, for Australia, for BrazilAIW-344FQ-N01 LTE/HSPA+/GPRF module, with GPS, for USAIW-344FQ-J01 LTE/HSPA+/GPRF module, with GPS, for JP
-
Product
MIL-STD-1553 Interface Board
EXC-4000VME/MCH-x / EXC-4000VXI/MCH-x
-
The EXC-1553VME/MCH and EXC-1553VXI/MCH cards are based on a MIL-STD 1553 certified "Summit" chip used in many flight critical systems. Each dual redundant channel supports both MIL-STD-1553A and MIL-STD 1553B protocols. Up to eight channels may be programmed individually to operate as a Bus Controller, Remote Terminal, Bus Monitor, or Remote Terminal / Concurrent Bus Monitor. The 32 K x 16 of RAM allotted to each channel for the storage of data and control parameters may be updated in real time.
-
Product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
Switch Blade
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
Filtered DC Interface Module
-
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
Intelligent Interface Card
Space Shuttle cPCI
-
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board). In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Single Port RS-422/485 Serial PCMCIA Card With Detachable Cable
SSP-200/300
-
The Quatech SSP-200/300 offers a convenient way to add a single RS-422/485 serial port to your laptop, PDA, or desktop (using one of Elan's Desktop PCMCIA adapters - P111, P222 etc.). The card automatically configures to become another COM port using the supplied drivers that are tried, tested, and optimized for Windows.
-
Product
Parallel Interface Voltage Output D/A Converters
-
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
PCI 8 Reed Relay Output / 8 Isolated Input Digital Interface
8012SH
-
The 8012SH is Universal Bus (3.3V and 5V) compatible and ships with the standard size PCI bracket to allow installation in a full-size PCI slot. If you have a Low Profile PCI slot, order the 8012H. The inputs on the 8012SH are rated for 10-30V. For 3-13V inputs, order the 8012S.
-
Product
FRP-25T Test System Interface Probe
FRP-25T
ICT/FCT Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1,210Overall Length (mm): 30.73
-
Product
8-port Serial Interface, Modular, With/without Optical Isolation, 3.3V/5V
APCIE-7800
-
The APCIE-7xxx series of ADDI-DATA allows you to implement either 1, 2, 4 or 8 modules on serial interface boards.
-
Product
BNC Box-D37M To 16 SE BNC Outputs For 24-Bit PCMCIA DAQ Cards
CB218S
-
*D37M input*16 Single Ended BNC Output Channels*Connects from Ines or Elan 24-bit PCMCIA DAQ cards via CBL-T30-32-D37F cable*Only for DMM i218, AD218 or AD218/i PCMCIA DAQ cards
-
Product
cRIO-PB-MS, Master/Slave, C Series PROFIBUS Interface Module
781352-01
Interface Module
Master/Slave, C Series PROFIBUS Interface Module - The cRIO-PB-MS connects NI programmable automation controllers (PACs) to PROFIBUS industrial networks as powerful masters or slaves. The interface includes the NI‑PROFIBUS for CompactRIO instrument driver for human machine … interface (HMI) and SCADA applications, as well as a graphical networking Configurator software. You can perform PROFIBUS device automated test using these interfaces. The cRIO-PB-MS is compatible with only CompactRIO systems.
-
Product
PCI 8 Reed Relay Output / 8 Isolated Input Digital Interface (3-13V)
8012S
-
The 8012S PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
PCI 16 Reed Relay Output / 16 Isolated Input Digital Interface (10-30V)
8004H
-
Optimized for sensing up to 24V inputs, the 8004H PCI digital I/O interface provides 16 optically isolated inputs and 16 Reed relay outputs. The inputs protect the computer equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide high quality, long-life, low-current (10 Watt maximum), dry contact switch closures. The relays are normally open, and close when energized.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
Interface
-
Interface devices convert one type of control signal to another, saving time and money by extending the life of existing field devices. Please see our Interface Matrix to assist in choosing the correct product.
-
Product
Ethernet Digital Interface OEM Board
8063
-
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
Product
Serial Digital Interface
Model 2363
-
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
Product
SIP-90-5 Test System Interface Probe
SIP-90-5
ICT/FCT Probe
Overall Length (mil): 1,000Overall Length (mm): 25.40Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
Multi-Protocol Interface for USB or Ethernet Equipped Computers
EXC-Unet2/Px
-
Multi-Protocol Interface for USB or Ethernet Equipped Computers
-
Product
KYK-13 Interface
IP-Crypto
-
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
Product
ICD 3 Test Interface Module
AC164113
-
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
Product
6U VPX Power Interface Board VITA 62
106PIBC601-0000R
-
6U Convection Cooled VPX Power Interface Board, VITA62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
USB 2.0 Interface Module
-
USB 2.0 modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 2.0 link untouched.
-
Product
100 Pin Breakout Interface
VSI-Breakout-100
-
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Serial Data Acquisition And Control Interfaces
-
ICS's Serial to Data Acquisition and Control Interfaces are IEEE-488.2 compliant and and provide GPIB functionality over a serial link. Click on a link or scroll down to access the appropriate Serial Digital Interface:Our Serial to Data Acquisition and Control Interfaces have non-isolated analog and digital signals. Click here for our isolated Serial to Analog Interfaces.
