-
Product
Flame Testing
-
Helping you ensure acceptable flammability and flame resistance for electronic products and components.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
Flame & Other Plastics Testing
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
Gas and Flame Detection System
Zero Two
-
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection.
-
-
Product
HVUL2 Horizontal Vertical Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVUL2 Horizontal Vertical Flame Chamber is designed for the flammability testing of plastic materials used in consumer electric devices and appliances per UL94. The chamber is constructed of stainless steel with a black interior and large sliding window for easy viewing. The HVUL2 includes a fully adjustable specimen support and a precision metered gas burner. Three digital timers with remote control are mounted on the inside back wall of the chamber, allowing for precise and simplified line-of-sight operation.
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Flame Spectrometer
-
The Flame spectrometer is built using industry-leading manufacturing techniques that help deliver high thermal stability and low unit to unit variation without compromising the flexibility and configurability that are the hallmark of Ocean Optics miniature spectrometers. New features such as interchangeable slits, indicator LEDs and simple device connectors deliver more freedom and less frustration.
-
Product
Needle Flame Test Apparatus
-
Needle Flame Test Apparatus is designed to carry out fire hazard testing. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. Testing with regard to fire hazards can be done by creating exactly the conditions occurring in practice. However, this is not possible in most instances. Hence for this test, the actual conditions are simulated as closely as possible by the Needle Flame Test Apparatus.
-
Product
Flame Burning Tester
DRK3024A
-
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
Flat Pin-Staked Flex Jumpers
Series 171 thru 173
-
Flat Pin Staked Flex Jumpers. Aries Flat Pin Staked Flex Jumpers combine thin, flexible, solid Copper conductors embedded between layers of tough, flexible, flame- retardant insulation.
-
Product
Flash Point Tester
-
A flash point tester is an instrument that determines the flash point of a sample.To find the flash point, heat the liquid in a container and then introduce a small flame just above the liquid surface.the temperature recorded as the flashpoint.
-
Product
One Channel Gas Controller
Surveyor 4B
-
Teledyne Gas & Flame Detection
Teledyne Gas and Flame Detection has designed the SURVEYOR 4B as a monitoring apparatus specifically designed to ensure the safety of boiler plants, battery charging rooms or small units where your operations are at risk due to the possibility of flammable gas leaks.Developed for quick, safe detection, the SURVEYOR 4B control module combines highly reliable monitoring, simple implementation and low costs.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Flash Point Testers
-
Flash point is the lowest liquid temperature at which a test flame causes sample vapors to ignite. Fire point is the temperature at which the test flame causes the sample to ignite and remain burning for ≥5 seconds.
-
Product
HVR-LS Horizontal Vertical Flame Tester
HVR-LS/HVR-LSS
-
This equipment meets the requirements of ANSI/UL94, IEC60950-1, IEC695-2-2 and GB Standard. It is used to test the appliances and plastic materials parts of electrical equipment for the horizontal, vertical flammability test. The product tank shell is irony spray, and configured a transparent viewing window, the digital meter shows the burning time, afterflame time, afterglow time, this device has beautiful appearance, is easy to use and has reliable performance.
-
Product
GC Detectors
-
Compact and modular, the new, second generation 5383 Pulsed Flame Photometric GC Detector (PFPD) offers greater ease of use, design flexibility, and analytical refinement than its predecessor, while retaining the proven technology features that laboratories around the world rely on for accurate results.
-
Product
Masks Flame Retardant Performance Tester
WKS-1208
-
WKS-1208 Masks Flame Retardant Performance Tester is used to test the burning performance of the mask after contacting the flame at a certain linear velocity. It is special test instrument for the flame retardant performance of masks.
-
Product
Horizontal Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
Product
Flashpoint
-
The MINIFLASH is a uniquely designed flash point tester for the determination of flashpoints of liquids and solids, using the GRABNER INSTRUMENTS flash point detection method of measuring the instantaneous pressure increase inside the continuously closed chamber due to a hot flame. The MINIFLASH flashpoint analyzer series is a new approach to flash point testing. It revolutionizes traditional methods, when it comes to safety, sample volume, speed and instrument size.
-
Product
Thermal Protective Performance Tester (TPP)
-
Sataton Instruments Technology CO., Ltd
Thermal protective performance tester (TPP) is to determine the heat transmission of protective clothing or textiles exposed to flame and radiant heat resources. The tester which can provide thermal protection index (TPI) calculated by software is the recommended tool for evaluation the potential of second degree burn of the materials to block convective and radiant heat penetration. Analysis software can display real-time temperature curve and automatically detect heat time curve to show Stoll curve for rating the thermal protective performance of tested textiles.
-
-
Product
Fire and Gas Detection System
-
An innovative, modular system that combines highly reliable programmable logic controller (PLC) technology with our advanced gas and flame field devices.
-
Product
Portable Gas Measurement Devices
-
Teledyne Gas & Flame Detection
Looking for portable gas leak detectors to protect your staff? Teledyne Gas and Flame Detection measuring devices meet all your requirements.
-
Product
SPI Flammability Tester (Vinyl Material)
TF318
-
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
Product
High Voltage Thick Film Planar Resistors
HVP
-
*High resistance resistors for high voltage circuits.*Thin SIP shape*The flame retardant coats corresponding to UL94V-O are used*Thick film resistors ensure high stabilities in life and change in aging
