Rotary Stages
Revolve a table in a circular motion.
-
Product
Transmissive Rotary Disk
DISK-2
-
US Digital offers a wide variety of standard rotary encoder disks. They may be ordered as a stand alone disk (see below) or as a codewheel (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable. There is no minimum order.
-
Product
Rotary Hex Drive Torque Sensor
-
Futek Advanced Sensor Technology, Inc.
The Rotary Hex Drive Torque Sensor category has Torque Sensors which are used in slip ring and non contact rotary torque measurements. The most common utilization for these models is for inline/reaction applications, where measurements can be made in both clockwise and counterclockwise directions.
-
Product
Stages
-
Applied Scientific Instrumentation
Consists of ASI's proven piezo top plate mounted within your existing OEM stage. This requires a completely new top plate be machined for the OEM stage, however, this allows us to provide an elegant solution.
-
Product
Waveguide and Coaxial Rotary Joint Assembly
-
Waveguide and Coaxial Rotary Joints are used for the transmission of power and signal between the locked and rotating parts of a radar or satcom system.
-
Product
Rotary Motion Logger Sensor
NUL-226
-
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
Product
Temperature Controlled Microscope Stage
-
Linkham Scientific Instruments
Specialists in temperature controlled microscopy, Linkam Scientific Instruments, announce the launch of their Optical DSC450 which enables simultaneous visualization of thermal processes for improved materials characterisation. The Optical DSC450 enables the user to measure glass transitions and melting behaviour of a wide range of substances whilst accurately controlling temperature from -196 °C to 450 °C. The atmosphere of the stage can also be purged with gas as required by the user. A new feature which will increase the characterisation capabilities of the DSC system is to combine it with imaging capability. The new LINK Digital Imaging module enables additional information to be obtained by correlating optical changes such as colour with temperature. The new TASC analysis tool takes this further. TASC (Thermal Analysis by Surface Characterisation) is a new image analysis capability which enables structural changes in samples to be tracked and quantified optically. It has the unique ability to measure local transition temperatures allowing different points on a sample to be identified. The new DSC system is great tool to use in research and quality control to measure quantitative values for glass transitions, melting peaks and sample purity and, when combined with TASC, even sample homogeneity.
-
Product
Rotary Torque Transducer
M425
-
M425 rotary torque sensor with keyway shafts offers high accuracy of 0.1% and torque measurement range from 0-10Nm up to 60,000Nm as standard. It’s an inline rotation torque transducer, widely used for motor, gearbox and pump torque testing.Using a highly-accurate non-contact technique, the Datum M425 Rotary Torque Transducer and Torque Meter represent an ultimate torque sensor for anyone looking to measure torque, power, and speed with high accuracy and repeatability.
-
Product
Thermal Microscope Stage
TS-4MP
-
With our TS-4MP Thermal Stage, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C
-
Product
Image Analysis & Stage Micrometers
-
The APPLIED IMAGE series of Image Analysis and Stage micrometers are ideally suited for calibrating optical, imaging, video, and reticle-based measurement systems. Designed for ease of use and manufactured for durability, the SM Series has both English and Metric scales in one or two axis configurations. Both types of micrometers come with NIST traceable calibration standards and are available on multiples substrates to perfectly fit your needs. The experience APPLIED IMAGE has in manufacturing precision imaged optical components makes us the trusted source for standards for magnification system microscopy and vision applications. Should you need to alter feature patterns, size, or substrate, fill out our Custom Optical Components and Standards form to start the conversation.
-
Product
Rotary Viscometer
NDJ-1
-
Viscometer is used to measure viscosity resistance and absolute viscosity of fluids, including liquid, oil, food, medicines, adhesive, etc.measuring range: 1-1x10 5 mPa.sError: 5%
-
Product
Fluid Rotary Joints
-
EVERAXIS Fluid Rotary Joints are designed to operate at extreme pressure and with high flow. The main application is the cooling of radar antennas. Fluid Rotary Joints are commonly integrated into rotary joint systems together with RF rotary joints, FORJ and slip rings.
-
Product
Rotary Encoders
-
Our proven rotary encoder and resolver solutions are used worldwide in a variety of industries such as Medical, Oil & Gas, Aerospace, Packaging, Robotics, Paper and Steel, to name a few. Dynapar''''s vast product portfolio offers a wide selection of incremental and absolute encoders engineered with cutting edge optical or magnetic technology, brushed and frameless resolvers, and accessories. Dynapar offers a wide variety of optical or magnetic shaft encoders and resolvers, as well as any resolver or encoder product your particular application may require.
-
Product
Rotary Encoders / Angle Sensors
-
Measuring and monitoring of rotary speed and rotary shaft positions at machines, installations and electrical drives
-
-
Product
Taber® Rotary Abrasers
5135 & 5155
-
The Taber® Rotary Abraser is an industry standard used in wear and durability testing and is available with either a single test head or dual testing heads, which allows the user to test two different or identical materials simultaneously.
-
Product
High-Dynamics PIMag Linear Stage
V-522 • V-524 • V-528
-
Physik Instrumente GmbH & Co. KG
Reference-class linear stage. Linear positioning stages with magnetic direct drives largely dispense with mechanical components in the drivetrain and the drive force acts directly on the motion platform. Together with precision bearings, a high travel accuracy and longer lifetime is achieved. The linear positioning stages are particularly suitable for scanning applications. PIMag® Voice Coil. Voice coil drives consist of 2 essential components: A permanent magnet and a coil, which is located in the air gap of the magnetic field. When current flows through the coil, it moves in the magnetic field of the permanent magnet. The direction of motion depends on the polarity. Thanks to their low weight and friction-free drive principle, voice coil drives are particularly suitable for applications, which require high dynamics and high velocities at limited travel ranges. High scan frequencies and precision positioning are also possible with these drives, because they are free of the effects of hysteresis.
-
Product
Hygrometer with 3 Stage Thermoelectric Cooler
CR - 4
-
Buck Research Instruments, LLC
The CR-4 is a chilled mirror hygrometer that uses a 3-stage thermoelectric cooler (TEC) to enable frost point measurements of as low as - 65C, under favorable ambient conditions. Depending upon ambient temperature, it can measure dew points as high as 60C.
-
Product
Non Contacting Rotary Position Sensors
-
We offer a comprehensive range of Hall Effect Non Contacting Position Sensors, from the World leading suppliers. Our range includes both Non contacting and Non touching Rotary Position Sensors.
-
Product
Rack Mount Stage Controller
RM-2000
-
Applied Scientific Instrumentation
*2U 19" Rack Mount Control Unit: 22.8D x 48.3W x 8.1H cm (9" x 19" x 3.2").*100 MHz Microcontroller for Faster Command Processing and Servo Control.*Closed-Loop DC Servo Control of up to Four Motorized Axes.*0-10 Vdc DAC Output for Additional Analog Control.*Firmware Upgradeable via Serial Connection.*Remembers Last Position on Power Up.*LCD Display Shows Axes Coordinates and Status.*USB or RS-232 Serial Control with Rates to 115200 Baud.*"Zero", "@", and "Home" Buttons on Joystick.*Left- or Right-Hand Joystick Unit.
-
Product
CNC Rotary Axis Calibrator
API Swivelcheck
-
API SwivelCheck is light-weight & comes with a convenient carrying case to easily transport & install on a variety of CNC machines.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Water Level, Stage, and Flow Sensors
-
Campbell Scientific offers a variety of sensors to measure water level, stage, and flow: pressure transducers, shaft encoders, radar ranging sensors, sonic ranging sensors, and bubblers. Users often select their sensors based on the site location, required accuracy level, and ease of installation.
-
Product
Stepper Motor,Precision Linear Stages,Application for Labs
PSAXXX-11-X
-
Model:PSAXXX-11-X Stepper Motor,Precision Linear Stages,Application for Labs Stepper motor and RS232 interface combine with SC300,MC series controller, achieve automatical control. Grinding ball screw ,linear slide and elastic couplings adopt high-quality products ,provide quality assurance . The design of limited switches and zero switch protect products and supply convenience;Standard interface is convenient for singal’s output. The back of motorized stages has handwheel , it is for convenience for adjustment; Standard hole is so easy for combine with other units, ensure convenience for multi-dimensional system; standard stepper motor and DB9 interface, choose to any controller according to requiremment
-
Product
Rotary Torque Sensor
RTSX
-
The Rotary Torque Sensor is the ideal torque-auditing tool for testing the actual torque being applied on the assembly application. By connecting a rotary torque sensor between an electric or pneumatic tool and assembly application, you can monitor the torque being applied from the tool to fastener or bolt.
-
Product
Multi Rotary Switches
-
Our multi-functional switches with Hall-effect or mechanical contact system are ready to provide a reliable long-lasting output. These switches can also fit evolving technical requirements.
-
Product
Crossed-Roller Bearing Linear Stage ,25mm Travel,Sensitivity 1um
NFP-1462
-
Model:NFP-1462 Crossed-Roller Bearing Linear Stage ,25mm Travel,Sensitivity 1um
-
Product
Rotary Thermal Shock Chambers
TS Series
-
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
Product
Brushless Rotary Torque Sensor
BLRTSX
-
The Mountz brushless rotary torque sensors are an ideal torque-auditing tool for testing the actual torque being applied on the assembly application. Particularly valuable for measuring torque on pulse tools with strong vibrations. By connecting a rotary torque sensor between an electric or pneumatic tool and the assembly application, you can monitor the torque being applied from the tool to a fastener or bolt.
-
Product
Rotary Torque & Angle Sensor
RTSX-A
-
The Rotary Torque & Angle Sensor is the ideal torque-auditing tool for testing the actual torque being applied on the assembly application. By connecting a rotary torque sensor between an electric or pneumatic tool and assembly application, you can monitor the torque being applied from the tool to fastener or bolt.
-
Product
Dual Stage Temperature Switch
TSS2
-
Regulate temperatures for heating or cooling control with the Series TSS2 Dual Stage Temperature Switch. The Series TSS2 is designed to accept two inputs with independent relays output for dual stage temperature control.
