Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-021
Programmable Resistor Module
The 40-297A-021 (PXI) and the 42-297A-021 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
3-Phase AC Power Source
61700 series
-
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
Product
Solar Array IV Curve Simulation Softpanel
-
Chroma Systems Solutions, Inc.
Easily program the I-V curve of the Solar Array Simulator with this test software as well as the I-V and P-V curves for real-time testing. See both dynamic and static MPPT efficiency and even simulate the IV Curve with shadows. The real world weather simulation function allows the user to simulate the irradiation intensity and temperature level from early morning to nightfall.
-
Product
8 Port BRI-U ISDN Simulator
BRI-8U
-
The unit has 8 U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Three Phase Phantom Load Test Bench
-
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
Product
Mobile Network Emulator
-
Qosmotec Software Solutions GmbH
QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).
-
Product
Dynamics & Transients Analysis Software
-
Dynamics & Transient analysis software enables engineers to simulate sequence of events including power system disturbances and evaluate system stability by utilizing an accurate power system dynamic model.
-
Product
Drop Test System
-
HIACC Engineering & Services Pvt. Ltd.
HIACC's Drop Test System is a specialized, automated testing apparatus designed to simulate real-world handling and transportation hazards, determining the "drop bearing capacity" (durability) of products and their packaging.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 2.97MΩ
50-297-051
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Loopbacks
-
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) has developed the Loopback TFOCA and TFOCA-II® plug configuration as an aid to system maintenance and troubleshooting of the tactical cable reels and systems that use them. The Loopback plugs come in a variety of configurations from 0 dB to -23dB to simulate a system operational condition. The use of the Loopback plug enables a technician to test a cable reel in the bi-directional mode by simply swapping leads on the test meter, thus saving considerable time and effort in establishing a systems operational status.
-
Product
Troposcatter Simulator
HTSS
-
Hollis Electronics Company LLC
Hollis Electronics HTSS is a quad diversity Troposcatter channel simulator which interfaces with your radio equipment at 70 MHz IF. The complete digital implementation provides high accuracy and exact repeatability. An integrated AWGN noise source coupled with an internal power meter supports accurate setting of SNR and Eb/No.
-
Product
AdvancedTCA, Type 11A, 5U 19" Horizontal, DC
11A06FJB58Y4HMXX
-
Elma's ATCA, DC, 5U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
Heavy Duty Dynamometers
MD-7500-HD
-
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
Product
SIMulation Workbench
-
A comprehensive framework for developing and executing real-time hardware-in-the-loop and man-in-the-loop simulations.
-
Product
Software Platforms
-
Discover complete solutions for Hardware-in-the-Loop (HIL) and Rapid Control Prototyping (RCP) testing. OPAL-RT offers the most advanced real-time simulation software platforms for power systems, power electronics, aerospace and automotive sectors: RT-LAB (Multi-domain, MATLAB/Simulink® based), HYPERSIM (Power Systems), and NI VeriStand (Automotive).
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
PXI BRIC4 FIBO Matrix Dual 93x4 2pin brkout
40-592A-013
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Test Solutions for Networked Vehicle Components/Connected Cars
Infotainment & Telematics
-
Developing automatic test systems for the automotive industry is one of our core areas. This industry in particular is characterized by rapid technological progress and ever faster time-to-market requirements.In the vehicle, multimedia devices are used for pure entertainment, but also as vehicle information, which are intended to cover security and navigation services.Infotainment and telematics devices such as eCall modules, connected gateways, instrument clusters or the HMI (Human Machine Interface) are networked with each other and with the most important vehicle functions. All of this is made possible - in addition to GNSS (Global Navigation Satellite System) - by wireless and new communication standards such as A 2 B, BLE, C-V2X, Wi-Fi 6 and 5G.The complex networking is a very attractive factor for drivers and passengers, but this complex communication can become a major challenge for developers.High-speed interfaces and high-frequency modules used in combination must send and receive signals between the different devices absolutely error-free.With our individual and sensitive test and inspection systems, we also simulate vehicle components or emulate the vehicle environment and thus ensure the functionality of your devices. We take your pioneering developments to the next level.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
Simulator
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 16 Channel
41-761-003
Simulator
The 41-761-003 is a low voltage 16-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 24 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
Network Emulation
-
PacketStorm Communications, Inc.
The PacketStorm IP Network Emulators and simulators reproduce the unfavorable conditions of IP Networks and WANs in a controllable and repeatable lab setting. PacketStorm is the Industry leader of Layer 2 and Layer 3 WAN emulation and network bandwidth simulation.
-
Product
MIMIC® MQTT Simulator
-
MIMIC MQTT Simulator is a scalable, customizable, programmable, predictable, dynamic simulation platform designed to enable rapid development / testing / deployment / tuning / training / demonstration of large-scale Internet of Things applications.
-
Product
Bus Analyzer
Goebelyzer
-
Our Goebelyzer analyzer systems offer unparalleled insight into bus data and are used in flight test, system simulation, LRU design, verification and manufacturing test. Supported Interfaces Arinc 664, ASCB-D, Honeywell Flight Controls P2P, Arinc 429, CAN2.0b, Mil Std 1553, RS 422 SDLC/Async, ADC
-
Product
Intel 80486 DX2 Processor Board
MS 1500
-
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 11.4MΩ
40-298-053
Programmable Resistor Module
The 40-298-053 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
-
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
