Outlet Testers
test access viability to electricity, gas or data.
-
Product
Surge Testers
MTC 2
-
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
Product
Hipot Tester
Sentinel
-
The Sentinel series of test instruments has been built to provide a cost effective, yet powerful solution to hipot testing, whether on a production line or in a laboratory environment for compliance testing purposes. With the ability to perform either 5kV AC or 6kV DC dielectric strength tests and up to 500VA AC power output the Sentinel series can aid testing to many international safety standards including IEC, EN, UL and CSA to name but a few.
-
Product
Electrical Tester
PRO T6-1000
-
The T6-1000 PRO Electrical Tester measures voltage up to 1000 V ac and current up to 200 A ac, all through the open fork and without test lead contact to live voltage. Connect the black lead to ground with the included heavy-duty alligator clip, slide the wire into the open fork and see both voltage and current at the same time. On wires up to AWG 4/0 (120 mm2), carrying as much as 200 A and 1000 V ac. Even with gloves on. It will change how you do your job.
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
Product
Capacitor Tester
MIG1212CAP
-
MIG1212CAP is specially designed for high voltage test on X / Y capacitors with impulse voltage approximate 1,2/50 µs up to 12 kV in accordance with IEC 60384-14 Ed.4. The MIG1212CAP comprises two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape of approximate1,2/50 µs and are combined in an 8 unit high 19" rack. IEC 60384-14 and EN 132400 define the generator.
-
Product
Anaerobic Jar Tester
LD-LAJ-A10
-
Anaerobic JarLD-LAJ-A10with 1.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Durometer Hardness Testers
-
IMADA, Inc., provides accurate measuring devices for every need. Some of the many high-quality instruments we manufacture are durometers. Durometers are important to the manufacturing sector because they measure the hardness of materials. These include normal and hard rubber, as well as soft and hard plastics, by assessing the resistance to indentation of polymers, elastomers, and rubbers. They do this by applying pressure to the surface of an object via an indentor and measuring the level of resistance. The results are expressed in terms of the Shore hardness scale, which varies based on the materials.
-
Product
Flying Probe Tester
FA1817
-
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
Product
DIN Abrasion Tester
TF215
-
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, transmission belts, soles, leather etc. The abrasion tester is provided with a wide testing area to meet the most requests. Additional balance is required.
-
Product
Single-Functional Testers
3122
-
The MI 3122 SMARTEC Z Line-Loop / RCD is designed specifically for live circuit testing. The instrument contains integrated characteristics of fuses and RCDs for the evaluation of test results. The online voltage monitoring system allows the operator to control what is happening on three simultaneous voltages in real-time. The bright red and green PASS / FAIL lights and help screens for each measurement make the handling of the instrument easy and clear. All the results can be quickly saved on the instrument and then downloaded via the optional A 1291 EuroLink PRO or A 1290 EuroLink PRO Plus software for evaluation and professional report generation after testing.
-
Product
VGA in Tester
M-IPC-520B
-
Fuzhou Metricu Technology Co Ltd
Analog camera testIP camera test, support onvif, 4K, H.264 and H.2658MP TVI test, 8MP CVI test, 8MP AHD testVGA input, support 1920 x 1200P 60FPS
-
Product
SoC Tester
UltraFLEXplus
-
The UltraFLEXplus combines new instrument and software capability with a revolutionary tester infrastructure that provides a step-function improvement in throughput and engineering efficiency – all while leveraging the cumulative test IP developed over the UltraFLEX’s 15 year history .
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Incline Impact Tester
KRD100 series
-
KRD100 series incline impact tester simulates the ability of product packaging to resist shock damage in the actual environment, such as handling, stacking of shelves, sliding of motors, loading and unloading of locomotives, product transportation, etc. This machine can also be used as a common test equipment for scientific research institutions, colleges and universities, packaging technology test centers, packaging materials manufacturing plants, and foreign trade, transportation and other departments to conduct incline impact test.
-
Product
Cable & Insulation Testers
-
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
-
Product
Fretting Tester
FFT Series
-
Fretting wear is a test where surface damage occurs between two contacting surfaces experiencing oscillatory displacement of small amplitude. At the contact point, lubricant/coating is squeezed out or the low amplitude motion does not permit the contact area to be re lubricated/ debris dislodge resulting in serious local wear occurs. This type of wear causes two-body abrasion, adhesion and/or fretting fatigue wear.
-
Product
Electrical Tester
T+Pro
-
Safer than solenoid testers and fully compliant with NFPA 70E, (when used properly per Article 110.4 Use of Equipment (A) Test Instruments and Equipment), the T+Pro helps electricians and technicians work safer by indicating the presence of voltage, even when the batteries are dead.
-
Product
Multifunctional testers
MI 3152 EurotestXC
-
MI 3152 EurotestXC is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN, TT and IT earthing systems are managed by a completely new user interface based on large colour touch screen display. A wide range of functions is included: from on-line voltage monitoring, phase sequence testing, varistor testing, earth resistance measurement, illuminance measurement and TRMS current measurement up to RCD tests, line and loop impedance tests, specific earth resistance measurements as well as ISFL measurements and the IMD tests.
-
Product
Insulator Testers
-
*Designed to test lightning arresters for damage or deterioration*Live line tester tests lightning arresters prior to energizing*For use on system voltages from 4kV to 25kV line-to-line and up to 69kV with optional add-on resistor sticks*Versatile for overhead and underground applications
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Flying Probe Testers
-
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
Product
Specific Gravity Tester
LD-LSGT-A10
-
Specific Gravity Tester LD-LSGT-A10 determines the theoretical maximum specific gravity of bituminous mixtures in accordance to ASTM D2041 Standard Test Method for Theoretical Maximum Specific Gravity of Bituminous Mixtures (Vacuum process). Adopted with single chip machine technology to shake a loose asphalt mixture sample submerged in water. Vacuum is applied into the sample, to extract out the air bubble.
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
Electronic Ballast Tester
WT5000
-
WT5000 is the updated version of WT3000 with a super LCD for displaying waveforms and parameters directly, and it includes all the functions and technical parameters of WT3000. Reports can be printed if printer is connected. It also meets the latest requirements for electronic ballasts in international standards IEC 60929, IEC 60969, IEC 61000-3-2, GB/T15144-2005, GB/T17263-1998 and so on.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Wire Bend Tester
-
CSZ chamber is designed for this type of cold bend test. Each chamber is designed to meet the customer's size and temperature requirements. Chambers feature power-driven mandrels that are typically mounted at the top and bottom of the chamber for the wire to wrap and bend around. Mandrel diameters are selected by the customer and supplied in a variety of sizes.
-
Product
Spark Testers
-
Range of portable and hand-held AC spark testers, kits, accessories and electrodes which are all specifically configured to suit a range of test applications.
-
Product
6-24V Circuit Tester
1656
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems. The most essential for troubleshooting automotive electrical systems. Make it easy to find out where current is present.
