Socket Testers
test access viability to electricity, gas or data.
-
Product
Open Top BGA Sockets
-
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
Product
Socket Outlet Torque Test Device
CX-LJ
-
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
Custom Socket
-
Different structure:open top,clamshell or handlerOne type: design socket according to customer's PCB.The other type : customer layout PCB according to socket datasheet.Please tell device voltage,current,frequency and temperature and other requirements.
-
Product
MultiSite Test sockets and Wafer Level
-
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
-
-
Product
Plug And Socket Torque Test Machine
-
Shenzhen Chuangxin Instruments Co., Ltd.
Plug Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. Plug Torque Tester is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
Universal PLCC ZIF (Zero-Insertion-Force) Test Socket
Series 537
-
Universal PLCC ZIF Test Socket Live Bug Type. This Universal PLCC ZIF (zero insertion force) Test Socket will take seven sizes of PLCC footprints with Aries insert plate, Part No. XX-537-20. Data Sheet No. 10012, available seperately.
-
Product
Universal Test Socket Receptacle
Series 6556
-
Universal Test Socket Receptacle. The Aries Universal Test Socket Receptacle is sturdy, open frame, and easily mounted to PC boards. Allows for easy replacement of Aries and other manufacturers test sockets. A choice of four collet pin styles makes the receptacle useful for any interconnection method.
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Rub Tester and Abrasion Tester
RT4
-
This comparative test works by abrading a printed sample against a reference material under known conditions. The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.
-
Product
Service Testers
-
Service tester with receiver probe, laser pyrometer, alligator clip cable, 10 inch handle, manual and standard bag.
-
Product
Cable Testers
E447
-
Similar to E445 but without jack and RCA (phono) testing facilities. Includes special XLR remote unit to enable testing of cables where it is not possible to bring both ends to the tester.
-
-
Product
Open-Frame Collet Socket with Wire Wrap Pins
Series 508
-
Open Frame Collet Sockets with Wire Wrap Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. 2 and 3 level wire wrap pins available. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
-
Product
Electrical Testers
-
The Fault Trapper is a new class of tester using Spread Spectrum Time Domain Reflectometry (SSTDR) to monitor energized circuits.
-
Product
Torque Tester
DIS-RL series (05/2/6)
-
Tightening and final check of screws and bolts. Separate type digital torque driver/wrench. The detection part is very compact, and it is effective for torque measurement in narrow places and minute torque measurement. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Shock Testers
-
Shock test data is key information when determining if your product is capable of withstanding its intended distribution and use environment. For any mechanical shock testing application, Lansmont builds a Shock Test System to meet your needs.
-
Product
Battery Testers
EEST 50-60
-
Charge/discharge and test benches for aerospace batteriesCharge/discharge benches for the maintenance, the certification, the training and the homologation of all industrial battery types
-
Product
EMF Testers
-
Shanghai Beha Electronics Co., Ltd.
*Handy EMF tester*Digital EMF Tester for Measurement of Magnetic Field Strength*direct display in Tesla or Gauss*Measurement Range:0...199,9 μT0...1999 mG
-
Product
HDBaseT Tester
-
The MS-TestPro is the only HDBaseT tester that is all-inclusive, 100% reliable, portable and affordable, making it an indispensable tool for all installers and integrators. It provides AV professionals with all the information that they need while in the field to enable them to verify the integrity and stability of every system tested down to the last detail. Moreover, the MS-TestPro generates a report including all the parameters necessary to certify link quality and status up to 4K Ultra High Definition. The report can then be transferred to a computer or even to a smartphone for use by both installer and end-user.
-
Product
Test Socket Based Elastomeric Matrix Connectors
-
Z-Axis offers a wide range of high performance test sockets, which are based on our elastomeric matrix connectors, for wide range of IC packages (BGA sockets, LGA sockets, etc.), coaxical, and wafer level; and for testing high speed, digital, analog, and RF signals etc.
-
Product
Three-Phase Smart Socket
WECO 3230
-
Utilize the RW-3X's features while on site in the van, as well as back at the shop with the WECO 3230 Three-Phase Smart Socket. The 3230 features built-in laser optics, Smart Socket™ technology and automatic meter form selection. Connect the RW-3X to the 3230 side panel using the included cables and the RW-3X Winboard Embedded software automatically sets the meter form, which will then populate on the WECO 3230 LCD display panel, and now you are ready to test. Not only does the 3230 make testing meters a snap, but it expands the current capability of the RW-3X to a full 50 amps, allowing the user to test class 320 amp meters.
-
Product
Insulation Testers
-
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
