Electrical Testers
-
product
Battery Tester
700
The #700 has an internal loading capacity of 100 amps. It is a great tool for finding batteries that can’t stand up to the load of today’s automotive accessories. It will also test relative starter current draw and charging voltage.
-
product
Safety Testers
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.
-
product
Mini Lan Tester
21-8572-00
Auto decipher the straight and cross-over pinning?RJ45 each pair connected display.
-
product
CT Polarity Tester
DIR CT
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
-
product
Multi-Channel Hipot Tester
19020
The hipot test is one of the major test items in electrical safety testing. All electrical components and products including transformers, capacitors, power supplies, chargers and home appliances require hipot testing.
-
product
EV And Pack/Module Tester
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
product
Industrial Battery Tester
The Industrial Battery Tester (IBT) has been designed for testing traction batteries or batteries for stationary applications. It can also be used for testing other types of batteries. The IBT performs charging and discharging in accordance with the programmed test schedule. Parameters are constant current, constant voltage, constant resistance and constant power.
-
product
Battery Capacity Tester
BLU-C Series
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
product
Electrical Laboratory
As one of North America’s largest and most diversified product testing and engineering service providers, Trialon provides a comprehensive range of EMI/EMC, ESD and Electrical testing solutions. Our EMC Testing Laboratory is ISO/IEC 17025 accredited, as well as being an approved facility for both General Motors and Ford Motor Company. Plus, we provide multi-shift support to assure programs meet time lines. Trialon’s EMC team has NARTE-certified personnel that will provide you with reliable and cost-effective testing that complies with a wide range of industry standards.
-
product
Vibration Unit Tester
BK2020B
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
-
product
Fuel Pressure Testers
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
product
DIN Abrasion Tester
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, leather etc. Abrasion Testing Machine complies with DIN 53516, ISO 4649, BS-903,etc.
-
product
WAN Tester
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
product
Concrete Hardness Tester
W-C-7312
It is recommended that calibration of the test hammers be checked regularly usually after about 2000 strokes.The James Calibration Anvil (W-C-7312) has been designed for just that purpose.
-
product
Cable Testers
TEST-9110 Series
Designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
product
Back Plane Tester
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
product
Endurance Tester
Premier's Endurance Tester, also known as on-off tester and life tester, is used to perform the life test of the unit. The Endurance Tester, switches on the unit for a set time and then turns it off for a set time. This entire cycle is repeated multiple times, to simulate the behavior of the unit under extended use
-
product
IK Level Tester
IK07-10
IK ratings are defined as IKXX, where “XX” is a number from 00 to 10 indicating the degrees of protection provided by enclosures (including luminaires) against external mechanical impacts. The different IK ratings relate to the ability of an enclosure to resist impact energy levels measured in joules (J). IEC 62262 specifies how the enclosure must be mounted for testing, the atmospheric conditions required, the quantity and distribution of the test impacts and the impact hammer to be used for each level of IK rating. The IK test applicate on lighting luminaires test according to IEC60598 (GB7000) and IEC60068-2-75 (GB2423.55).
-
product
Macro Hardness Testers
Macro hardness is the measurement of the hardness of materials tested with high applied loads.
-
product
Load Stability Tester
TruMotion™ Acceleration
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
product
Two-Pole Voltage Tester
P-6
SONEL P-6 has all the features that characterize the P-4 Voltage Tester and P-5 Voltage Tester. In addition, the P-6 model has the phase identification function which allows to verify the phase compatibility (and its overtaking or delay) against the phase at the reference object.
-
product
Hydrostatic Head Tester
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
product
Cable & Insulation Testers
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
product
Radiant Imaging Tester
Lumere-ZeM
Evolusys Technologies Sdn. Bhd.
• CIE matched color filters and neutral density filters• Wide range of working distances and aperture settings• Color and light measurements
-
product
Portable Hydraulic Testers
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
product
Automated Multi-Functional Tester
QTouch 1408 C
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
product
NI Electric Motor Simulation Toolkit
PMSM, ACIM, SRM, and power inverter models for high-performance simulationHigh-fidelity simulations with support for user-defined parameter lookup tables or JMAG-RT models. Open software for full flexibility and customizationLabVIEW project templates to build a software-only simulation and hardware-in-the-loop application. Direct integration with NI VeriStand for configuration-based real-time test. Models for desktop simulation, LabVIEW Real-Time simulation, and FPGA-based simulation
-
product
LCD Cable Testers
Shenzhen Noyafa Electronic CO.,LTD
The main function of NOYAFA LCD Cable Tester is to measure the cable length and check cable errors, by using LCD display can clearly shows the test results to users, making the faulty points visable, so that to save users time and effort.
-
product
Fiber Stiffness Tester
DRK023B
Shandong Drick Instruments Co., Ltd.
Used to determine the bending properties of various fibers.
-
product
sonic tester
PR-82
The PR-82 sonic tester has been modified for the automotive industry. This gauge is commonly used for measuring the thickness of cylinder walls, head ports, decks, tubing, body panals, and windshields. It also has the ability to scan the length of a part to find the the minimum thickness.The PR-82 is back-lit and the unit operates for up to 200 hours on a single set of batteries. It is protected by Dakota Ultrasonics 5 year limited warranty.
