IV
measure of current flow as a function of voltage.
-
Product
Voltage & Continuity Tester
ET250
-
The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.
-
Product
Flat Field and Imaging Gratings - Type IV
-
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Type IV aberration-corrected flat field and imaging gratings are designed to focus a spectrum onto a plane surface, making them ideal for use with linear or 2-D array detectors.These gratings are produced with grooves that are neither equis-paced nor parallel, and are computer optimized to form near-perfect images of the entrance slit on the detector plane.
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
Source Measure Units (SMUs)
B1511B
-
The SMUs of B1500A integrate 4-quadrant voltage/current source and measurement capabilities for accurate IV measurement with the range of 0.1 fA - 1 A / 0.5 µV - 200 V. It supports spot, sweep, pulse sampling and QS-CV measurements.
-
Product
2-Channel Front End
BEQ II.1
-
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
Product
Engineering Design & Development
-
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
-
Product
PV Test Solutions
-
High-speed and high-accuracy measurement of solar cell I-V characteristics in three modes
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Three-Pole Lighting And Surge Arrestor
PIVM12,5-275/3+0 Vseries
-
PIVM12,5-275/3+0 Vseries is a three-pole lightning and surge arrester Type 1+2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 0 – 1 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of both, the lightning current and the switching surge, which are generated in power supply systems entering the building. The use of the lightning current arresters PIVM12,5-275/3+0 Vseries is mainly in the power supply lines, which are operated as TN-C system. The main use of PIVM12,5-275/3+0 Vseries arrester is in structures of LPL III – IV according to EN 62305 ed.2. The marking M specifies a type of construction with removable module.
-
Product
3 Phase Meter - Anti-Clockwise
135012
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
Precision Source / Measure Unit, 1 CH, 1 PA Resolution, 21 V, 1.5 A
B2901BL
-
The Keysight B2901BL precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
Product
AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
ACDC-52NAV
-
The ACDC-52NAV clamp-on power meter is the ideal choice for jobs that require AC/DC current measurements to 600 A, AC/DC voltage to 1000 V and wide jaws to accommodate large conductors.
-
Product
IV Characteristics Measurement Device Software
Keithley 2400, 2401 and Keithley 2450
-
*Windows 10, Windows 11 (Compatible) RS-232C (Keithley 2400, 2401), USB (Keithley 2450)*NI GPIB can also be used (optional)*IPCE PEC-S02 can be used simultaneously. operation panel. *Everything from condition setting to measurement can be done on one screen.
-
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
-
Product
DELTA™ IV 4-zone Flow Ratio Controller
-
DELTA™ IV 4-zone Flow Ratio Controller is a digital controlled, browser-enabled, process control instrument providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution for semiconductor, flat panel, and solar panel process uniformity and control. It is available in EtherCAT® or DeviceNet™ providing the latest gas flow ratio measurement and control technology to meet the demands of multi-channel flow distribution.
-
Product
3 Phase Meter - Clockwise
135007
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
Reference Cells For PIV-IV Systems
-
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
-
Product
Precision IV Analyzer / 8 Slot Precision Measurement Mainframe
E5270B
-
Keysight E5270B Precision IV Analyzer is the complete solution for current-voltage characterization of a wide range of materials and devices. The E5270B supports multiple SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 0.1 fA. Its modular architecture allows you to configure or upgrade SMU modules for available eight slots. The EasyEXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5270B the best solution for characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency.
-
Product
Infusion Pump Analyzer
FT-2 FlowTrax®
-
The STANDARD FT-2 FlowTrax® IV Pump Analyzer provides the fastest, most accurate test results – within a remarkable 3 minutes. Integrated full-featured pressure & temperature meters plus digital timer saves the time and cost of buying/calibrating four devices!
-
Product
Products for High-Frequency Measurement
-
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
Product
Light I-V Testing for Modules
FMT-500
-
Advanced analysis of solar modules including light I-V and Suns-Voc data. Capability to accurately measure high-efficiency modules.
-
Product
Automated I-V/AOI/EL and Sorting System
-
OAI’s High Performance In-line Automated-I-V Testing, AOI/EL Inspection and Sorting/Binning System for Various Si Solar Cells. The 10000A-I-V System is a unique and reliable I-V testing, AOI/EL Inspection and Sorting / Binning system for testing of Mono, Multi-Si, C-HJT and other full Size (156mm x 156mm) and/or Cut-cell (156mm x 39mm or 156mm x 31.2mm or other custom sizes) Si Solar Cells.
-
Product
Voltage and Continuity Testers
-
Amprobe voltage and continuity testers have built-in shakers for fast, easy troubleshooting with CAT IV 600V/CAT III 1000V input protection. To safely detect voltages up to 122kV without contact to the current carrying conductor, choose an Amprobe high-voltage tester. These intrinsically safe tools are ideal for industrial, utility, and mine applications.
-
Product
TRMS System Multimeter for Use in Medical and Hygienic Sensible Ranges
SECULIFE HIT MD
-
TRMS multimeter that has been designed especially for all hygienically sensitive areas. 23 multimeter functions. Voltage measurement.Auto-ranging current measurement from 100A (resolution: 10nA) to 10A (16A). Capacitance and resistance measurement, diode and continuity testing. Measuring categories: 600V CAT III and 300V CAT IV. Hygiene certificate from University of Marburg
-
Product
Precision Source/Measure Unit (SMU)
B2900A Series
-
The Keysight B2900 Series precision source measure unit (SMU) provides superior performance and usability at a reasonable price. These compact benchtop SMUs enable you to quickly take various I-V (current versus voltage) measurements requiring high resolution and accuracy. Easily view results on the user-friendly, color LCD graphic interface without changing connections.
-
Product
Camera Based Beam Propagation Analyzer: M2
BeamSquared
-
The BeamSquared® system is a compact and fully automated tool for measuring the propagation characteristics of CW and pulsed laser systems from the UV to NIR to Telecom wavelengths. Users can also measure wavelengths above 1.8 microns, including CO2 and terahertz in manual mode (a bench set-up; without the automated optical train) with a Pyrocam IV or IIIHR. Our longer optical train and patented Ultracal™ Calibration makes BeamSquared the most accurate product on the market and is ISO 11146 compliant. Its operational robustness and reliability ensures continuous use applications in industry, science, research and development.
-
Product
Audio Frequency Oscillator
PD-5
-
2.5- 100 volt output6 position output voltage selectorCompatible with all "Mark" receivers (Mark II, III, IV, V)Pulse "Identifying" signalBattery charging circuit built-inLED impedance meter
