MIL-STD
ensures a product meets military standards.
See Also: Mil, MIL-SPEC, Mil-Std-1553, Mil-Std-1760
-
Product
PC Card
Flex1553 PCIe
-
The Flex1553-PCIe is a PCI Express card supporting 1, 2 or 4 Dual Redundant MIL-STD-1553 buses, 1553 Enhanced Bit Rate, ARINC 429 and Discrete with precise timing and flexible programming. The PCI Express card with a robust 19-inch connect panel for easy and long-lasting connectivity.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
/883 Op Amps & Buffers
-
Renesas offers MIL-STD-883-compliant operational amplifiers and buffers that are qualified to QML Class Q military standards.
-
Product
Rugged Cabinet
MS Series
-
The M-Series MIL-STD Cabinet offers a high level of integrity with its all-welded 12 gauge steel frame construction, and eight, 3-dimensional support braces (12 gauge), providing added resistance to demanding compressive and torsion loads.
-
Product
VME Intelligent Interface Card
IIB-1553-VME
-
The IIB-1553-VME is an intelligent interface card for dual redundant MIL-STD-1553 applications.
-
Product
Two Port Fibre Channel/MIL-STD-1760E Network Interface Controller
cPCI-HS1760-NCSW-2
-
Avionics Interface Technologies
Integration of Up Fibre Channel and Down Fibre Channel interfaces - Embedded Network Controller (NC) with four priority levels - Two F/AE ports for communication to external devicesInternal four port non‐blocking fabric switch for communication between NC and external devices - Four port non‐blocking Fibre Channel Switch - Meets the requirements of MIL‐STD‐1760E and AS5653 standards - Initialize via the Fast Fabric Initialization (FFI) protocol - ANSI C API enabling complete FC-AE-1553 NC functionality and management - 3U Conduction-cooled Compact PCI module - Designed for extended temperature operations
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Data Processing System
CRS-D8I-3VF1
System
The CRS-D8I-3VF1 VPX system’s I/O flexibility is capable of meeting a large number of configurations. It is designed to support Abaco Systems’ Intel 3rd generation Core i7 3U SBCs, Gigabit Ethernet switch, video compression card, CUDA-based graphics cards and a MIL-STD-1553/ARINC429 multi-protocol card.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
USAF Targets
-
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
