Fixed Attenuators
Fix the degree of attenuation.
-
Product
Variable Optical Attenuator - MATRIQ
Attenuator
The VOA MATRIQ Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fibre types and various wavelengths to suit a wide range of applications.With a stackable, space-saving design and intuitive software controls make it a valued addition to the optical lab or test bench.
-
Product
Programmable Step Attenuator, DC to 40 GHz, 0 to 11 dB, 1 dB steps
84904L
Attenuator
The Keysight 84904L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 11 dB in 1-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2.4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 90 dB, 10 dB steps
84906K
Attenuator
The Keysight 84906K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 90 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Attenuators
-
CAES offers a full range of RF Attenuators for your designs including analog and digital PIN Diode as well as Switched-bit Attenuators.
-
Product
Attenuator / Switch Driver
11713E
Attenuator
The 11713E attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
Fixed Terminations
-
Fixed Terminations absorb RF & microwave energy and are commonly used as dummy loads of antenna and transmitter.They are also used as match ports in many multi-port microwave device such as circulator and directional coupler to make these ports which are not involved in the measurement be terminated in their characteristic impedance in order to ensure an accurate measurement
-
Product
Attenuator
J2140A
-
Characteristic RatingMaximum Input Level +20dBm3dB Frequency Range DC ~ 50MHzMaximum VSWR 1.3Attenuation Accuracy 0.2dB
-
Product
PXI 5 Ch. Differential Hi Voltage Attenuator
41-661-001
Attenuator
High voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Digital Attenuator
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The products can be used in microwave electronic components. Its attenuation values are determined by the input TTL/LVTTL control signal. So that the link can be achieved the desired gain or loss value.KeyLink's digital attenuators can be categorized as follows.
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Variable Attenuator
FTBx-3500
-
Network equipment manufacturers and transceiver manufacturers know that variable attenuators are essential components of their test systems. They look for performance, user-friendliness, complete control of test parameters and advanced programming capability. EXFO’s FTBx-3500 Variable Attenuator combines innovative design techniques, high-quality components and meticulous calibration procedure. Ideal for bit error rate testing and system verification, the FTBx-3500 is the only variable optical attenuator (VOA) that offers a fully remote user interface (UI) and EXFO Multilink compatibility. It is also the only VOA on the market to offer a benchtop unit, which can be controlled remotely or using a touchscreen.
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
Product
Fixed Gas Analyzer
Model 1000
-
Teledyne Gas & Flame Detection
Natural gas pipeline monitor to detect H2S and CO2.Detcon Model 1000-CO2 and Model 1000-H2S Analyzers are designed to provide continuous, accurate, real-time measurement of gas concentrations in a wide variety of process gas streams. The instrument package is rated for Non-Hazardous areas.Consult commercial brochures for measurement ranges and more product features.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
-
Product
Attenuators
-
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
Product
Variable Attenuators
-
Continuously variable attenuators from Pasternack are available in 50 Ohm impedance and with SMA connectors. SMA continuously variable attenuators have RF db attenuation values that range from 7 dB to 40 dB. The frequency range of our continuously variable attenuators is from 1 GHz to 18 GHz. This variable attenuator product line includes low to high power attenuators which have the power handling up to 5 Watts.Variable attenuators from Pasternack include female genders and can be bidirectional, depending on the power rating. Our continuously variable attenuators are manufactured to precise industry specifications and the bodies are constructed of. Pasternack commonly uses Pi attenuators or Pi pads for its continuously variable attenuator designs.
-
Product
Attenuators
-
Reduces the amplitude of a signal without appreciably distorting its waveform.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Variable Optical Attenuators
-
Nanning Xionghua Photonics Technology
Variable Optical Attenuator by Xionghua Photonics
-
Product
Fixed Gas Detectors
-
Crowcon offers a flexible range of fixed gas detection products which are able to detect flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment. We use a variety of measurement, protection and communications technologies and our fixed detectors have been proven in many arduous environments, including oil and gas exploration, water treatment, chemicalplants and steel mills.
-
Product
Voltage Variable Attenuators
-
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Product
Step Attenuator
RSC
Attenuator
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
-
Product
Programmable Digital Attenuator
LDA-602EH
-
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
-
Product
Manual Step Attenuator
WATT-3SM352
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Fixed Area Hydrogen Monitor
HY-ALERTA™ 600B
-
H2scan’s HY-ALERTA™ 600B Fixed Area Hydrogen Monitor will provide hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. They are designed for either ceiling or wall mount and have RS422 capability that extends the interface from the sensor to the controller to several hundred feet. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to any other combustible gases, thus eliminating false positive alarms and increasing system reliability.
-
Product
Package Converters & Fix Adapters
-
Package converters provide an electrical and mechanical conversion from one package type to another. We use gold plated interconnects for our pin and through hole converters. Ironwood Electronics offers solder column adapters as a solution for leaded SMT packages such as QFP, PLCC, SOIC, SSOP, and TSOP. This is an excellent choice when you have a PC board in production that needs an upgrade or you need to replace an obsolete part.
-
Product
Fixed Units
-
A task type that keeps the assigned resources' percentage of time (availability) constant, even if the duration or total work required for the task changes.
-
Product
FIxed Energy Meters
-
Provide a consistent price per kilowatt-hour for electricity or gas, remaining unchanged for the duration of a contract.
