Kelvin Leads
A spring clip where the jaws are insulated from each other at the hinge point. 4-wire
-
Product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 72", 024070
VFL103124-072
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
-
Product
Kelvin Clip Set
11062A
Accessory Kit
Create custom Kelvin probes for 4-wire resistance measurements; set contains only the two gold-plated clips
-
Product
200 Pin Male LFH to TriPaddle Flying Lead Cable, 60", 441655000-1
VFL135106-060
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 200 pin Male LFH to TriPaddle Leads, 28AWG Twisted Pairs - MULTI LEG 100 T/P's (1:2) 200 connection points, 4-40 fastener, VPC: 441655000-1, for 40-148-101, 40-148-201, 40-148-001, 40-140A-221, 40-140A-121, 40-140A-021, 40-670C-022 families, VPC contact 610110167 - TRI RCV (26-28AWG) (7 AMP/4 mΩ MAX), 60" length.
-
Product
Test Leads
-
designed for electrical and electronics testing in today’s industrial environment.
-
Product
Kelvin Probe Set
11059A
Accessory Kit
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
Product
Test Leads
-
Test leads for digital multi-meters (DMM), tone generators, butt sets, oscilloscopes, and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
Product
Precision Kelvin Holders
MH-4 Series
-
Integrating Spheres are essential tools for photometricresearch laboratories & lamp / luminaire manufacturers. To derive the best results from Integrating Sphere Photometry, precision lamp holders are necessary.
-
-
Product
Kelvin Test Contactor
cCruiser
-
cCruiser™ Kelvin contactor was designed with cost of test optimization in mind, boasting a cantilever design that allows the testing of challenging discrete ICs and small logic package types. Providing a best-in-class proven lifespan of up to 5 million touchdowns increasing handler uptime. cCruiser reduces the cost of test for customers significantly, lasting longer and testing longer than previous contact solutions.
-
Product
Beam Lead Capacitors
-
Beam lead capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which allow for use in military and aerospace designs. Their robust performance and small form factor provide repeatable performance.
-
-
Product
Ultra-High Vacuum Scanning Kelvin Probe
-
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
-
Product
Ultra-High Vacuum Ф4 Scanning Kelvin Probe
-
The Ф4 Ultra-high Vacuum Scanning Kelvin Probe system gives the user full access to work function measurements under vacuum with the ability to alter the temperature from 77 K to 860 K. The Kelvin Probe measurement has resolution of 1 - 3 meV for a 2 mm tip on a conducting sample. The sample is mounted on a plate that is located on a motorized (x, y, z) translator attached to a stainless-steel vacuum chamber. Phi 4 also comes with a photoemission spectroscopy system with a tuneable source (3.4 - 7.0 eV). The deep ultra-violet (DUV) light spot measures approximately 3 x 4 mm. Absolute work function measurements can be obtained with this system in the range of 4.0 - 6.5 eV with an accuracy of 0.05 - 0.1 eV.
-
Product
Calibration Lead Precision Resistor - Single
40-975-009-SL1
Calibration Lead Cable Assembly
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
Flying Lead Probes
FLP850
-
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
Product
Extendible Test Leads
-
The Extendable Tip Probe permits testing in those hard to reach areas. The tips are fully insulated with durable Kynar. This prevents accidental shorting of adjacent components. The tip is stainless steel and is very sharp, allowing for penetration of conformal coatings. The rubber lead is 18 gauge, 48" long.
-
Product
Off-Set Kelvin Test Sockets
-
This is an innovative and robust contact technology for making Kelvin contact to 0.5mm pitch QFNs. The contact uses a tip that is angled to one side, matched to an orientation that's flat on the tip. Two such contacts placed in opposition will touch the pad within 0.125mm. And because the tip is offset, the probe diameter is a robust 0.39mm and the load board pad pitch remains 0.5mm.
-
-
-
Product
Leading Edge Sensors
-
The LaserGauge® Leading Edge Profiling System consists of a handheld or benchtop sensor and the Leading Edge software application. Designed to scan both sides of the blade simultaneously, the sensor returns a complete profile around the radius of the blade, which allows accurate measurements of the thickness and the plotting of the blade profile for comparison to its engineering design.
-
-
Product
Lead Screw and Nut Assemblies
-
Kerk Lead Screw Assemblies are modified Acme thread forms optimized for performance and available in a broad range of lead screw diameters, leads and nut styles, custom designed for your application. Kerk lead screws are self-adjusting, maintenance-free and require no lubrication.
-
Product
Capacitors - Beam Lead
-
Macom Technology Solutions Holdings Inc.
MACOM’s MMI-9000 and 9100 Series Chip Capacitors feature high stand-off voltage and low dielectric loss leveraging nitride/oxide dielectric layers. Gold bonding surfaces, top and bottom provide ease of bonding and minimum contact resistance. MACOMs beam lead capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which are features that produce devices with excellent long-term stability.
-
Product
DMM MULTIMETER TEST LEADS
-
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
-
Product
RS232 9 Way D-Type lead
1081-001
-
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
Product
Ambient Single Point Kelvin Probe System
-
This single point Kelvin Probe System operates under ambient conditions and is small enough to be placed in a customized glowth box. The probe head operates with an oscillating membrane and can be easily exchanged. The preamplifier is integrated inside the probe head.
