-
Product
Fixturing
-
Terotest specialises in providing test solutions specific to customers' test applications. We understand that the interfacing and fixturing of a particular test setup can determine whether the application is a success or a failure, and therefore we strive to deliver solutions that are cost effective and suitable to user requirements.
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
Product
Test Fixture
N1295A
Test Fixture
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
Accessories For Instruments And Fixtures
N1254A
Accessory Kit
The N1254A includes several optional accessories and adapters for instruments.
-
Product
Clamshell Type Mechanical Fixtures
Series 11
-
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
RF Signal Generator
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Genrad 2270 Interface Receivers
GR Series
-
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
Product
Test Fixtures
-
At A.T.E Solutions we have a dealt with a wide range of test subjects in the past 30 years and have extensive experience in providing reliable test fixture solutions.
-
Product
Serial Distance Display
TA903-03
-
This panel mounted or portable display will read Bendix/King serial distance as generated by their DME systems or GPS products. This long standing three wire format of CLK, DATA and REQ can now easily be displayed without the expense of a KTS143 test fixture. This product is ideal for shop and aircraft troubleshooting. The extruded aluminum enclosure is a standard DIN size(1/8) and the unit interfaces through a 25 pin D connector.
-
Product
Photometric Testing Services
-
LLI. offers a wide variety of services to fulfill your photometric, color and electrical testing needs. Using our custom, rotating mirror, Type-C goniophotometer, in combination with various integrating spheres, we are able to test many different types of lighting fixtures and light sources. LM-79 -08 Test & LM-80 Test, SSL Photometry Testing, Energy Star®, CEC Title 24, DesignLights Consortium® (DLC), Custom Tests and UL / ETL Safety Test Consultation.
-
-
Product
Bending Stiffness Test Fixture
-
Q-Card’s bending stiffness fixture features splayed feet and aggressive no-slip rubber pads for stability. It is manufactured of aerospace-grade aluminum alloy with a hard anodized, scratch-resistant, durable finish to provide years of rigorous testing and trouble-free service.
-
Product
Architectural Preset Stations
SceneStation
-
Interactive Technologies, Inc.
SceneStation sets a new standard for full-featured, easy to use, cost-effective DMX lighting control. SceneStation is entirely self-contained in a single gang wall switch sized unit. Perfect for restaurants, high-end residential, trade show booths and more, SceneStation can control nearly any DMX device (RGB fixtures, moving lights, dimmers, effects, etc.), while also remaining very simple for the end user.
-
Product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
Coaxial Cable
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
Product
CAM/GATE Test Kits
-
The Camgate ™ series test fixtures provide ‘Z’ axis motion and, with the optional floating top plate, makes this series ideal for top side probing. The floating push plate is accurately registered with two tooling/guide pins. The top plate mounting frame is adjustable in .500″ (12.7mm) increments to accommodate top side probing in the lower position, or clearance for PCA’s with tall components in the middle or top position, without the need for riser blocks. Camgate fixtures are available with the most widely used interfaces in the test industry.
-
Product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
-
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
Product
SHC68-C68-D4, 68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - 2m
781293-01
Digital Cable
The SHC68-C68-D4, 2m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Test Accessories
-
By combining the latest in LED technology with the unmatched illuminating dynamics of prismatic glass, this High Bay LED luminaire brings a superior, incomparable proficiency and reliability to the table. With its remote driver capability, the TDK HBLED-540 High Bay LED Light Fixture is ideal for EMC chambers with minimal RF emissions.
-
Product
Aircraft Test Set
CA-2100S-07
-
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
Product
Test Stand, Fixture Design and Manufacture
-
As your partner, Trialon’s commitment to providing our customers with custom test stands, test and vibration fixtures that optimizes the sample test. Our experienced staff can design and manufacture a test stand or fixture for almost any product.
-
Product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
-
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
PXI Test Instrumentation
-
The Yelo Pixi general purpose tester is a PXI based functional test system with in-circuit and continuity capability. Built into a free standing 19” rack is a PXI chassis, mass interconnect fixture interface, PC, flat screen and space for additional user selectable instrumentation.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
Deep And Sloped Pan Fixtures
-
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
Product
Dedicated Testers
-
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
