Parasitic Voltage
draw on battery when vehicle is off.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Safety Voltage Detector ( Rechargeable Battery Type )
350 SVD
-
Standard Electric Works Co., Ltd
● Protection class: IP65● Bright LED visual indication● Audible indication● Non-contact voltage detection: 220Vac ~ 132kVac● Wide angle voltage detection● Frequency range: 40 ~ 70Hz ● Easy-to-prove method● Self-test function● Power source: 9V rechargeable battery ● Non-contact detection by proximity● Flashlight function● Operating temperature: 0°C~50°C● Humidity: 80% RH Max● Lightweight, robust and compact● Comply with EN 61326-1
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-15KVe
-
The MI-15KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3.000.000 MΩ with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV.
-
-
Product
Work Area Voltage Detectors
-
*Warns of high voltage electric fields using WAVi technology - Work Area Voltage Indication*Visual and audible warning indicates the location of energized fields in a red-yellow-green sequence*Detectors communicate with each other within a mesh network*Remotely control detectors through the Lookout mobile app*Battery life of up to 500 hours in Monitor mode and up to 8 hours in Alert mode*Durable water-resistant housing
-
Product
Voltage Probe
VOL-PBE
-
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
Product
AC Voltage Test Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Retractable Cable + Automotive Voltage Tester
3702
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 24 and 48V DC systems. DC voltage mesurement and used as an extension cord for testing electrical circuits in cars , trailer, boats.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-314-HI
-
The 40-230-314-HI (PXI) and 42-230-314-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Low Voltage Test System
CKT T1
-
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-152-HI
-
The 40-230-152-HI (PXI) and 42-230-152-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Surge Testers
10000HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
Voltage & Continuity Testers
-
Our range of CombiVolt voltage testers are designed to measure AC/DC voltages and continuity. Most models provide LED indication, an audible tone or a combination of both while others have a digital display to give an exact reading, all testers have a non RCD Trip feature
-
Product
2kV, 120 MHz High Voltage Differential Probe with Auto Zero Disconnect
HVD3206A
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
PXI High Voltage Programmable Resistor Module, 1-Channel, REDEL Connector
40-230-345-HI
-
The 40-230-345-HI (PXI) and 42-230-345-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-124-HI
Programmable Resistor Module
The 40-230-124-HI (PXI) and 42-230-124-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-110-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-111-HI
-
The 40-230-111-HI (PXI) and 42-230-111-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 62.1Ω with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865683-01
-
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9205, cDAQ-9171, and cRIO-9940 includes the NI-9205 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9205 features a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Additionally, the NI-9205 provides up to 60 V of overvoltage protection between input channels and common, and it is rated for 1,000 Vrms transient overvoltage protection.
-
Product
Probe Oscilloscope High Voltage
-
High voltage probes allow safe and accurate voltage measurement using your oscilloscope.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
40-321-121-HI
Multiplexer Module
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
High Voltage Divider
-
HIGHVOLT Prüftechnik Dresden GmbH
Is a passive linear circuit that produces an output voltage (Vout) that is a fraction of its input voltage (Vin). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them.
-
Product
Cross Voltage Testers
-
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-013-HI
-
The 40-230-013-HI (PXI) and 42-230-013-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Unterminated for Pickering
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-325-HI
-
The 40-230-325-HI (PXI) and 42-230-325-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Series Voltage References
-
Analog Devices offers a broad line of series voltage references with low dropout, low power, and excellent line regulation. These devices are voltage references that are functionally similar to a three-terminal regulator. Some series voltage references are designed to also operate in shunt mode by biasing the output pin and leaving the input pin open circuit. Series mode voltage references have the advantage that they draw only load and quiescent current from the input supply.
