-
Product
AC / DC Current Clamp
HT9025
-
HT9025 has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/ EN61010-1.
-
Product
AC Current Digital Clamp Meters
-
Precision Mastech Enterprises Co.
Handheld, safe, and non-contact electrical tools designed to measure alternating current (AC) without disrupting the circuit
-
Product
High Voltage Probe, 100:1, 3.7 KVpk, 500 MHz
10076C
High Current Probe
The Keysight 10076C 3.7 kVpk, 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today's small power electronics components, and its rugged construction means it can withstand rough handling without breaking.
-
Product
Shunt Assembly
RSA-8
-
The RSA-8 Recording Shunt Assembly contains 8 individual shunts with terminal block programming for either a current channel (using the shunt) or bypassing the shunt and using a dropping resistor for conversion to a voltage channel.
-
Product
Split type AC Current Sensor
CTF-100A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Precision Shunt Chip Resistors
SMV
-
*5W permanent power at 65C*High pulse power rating*Mounting: Reflow and wave-soldering
-
Product
Working Standard Shunts
CSW
-
CSW shunts are rated to 100 % continuous current with no loss of accuracy. They are largely immune from connection errors common to many shunts. All CSW shunts include ISO17025 accredited calibration through full current range.
-
Product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
Battery Probe
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
Product
AC DC Current and Voltage Converters
-
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
Product
Split Type AC Current Sensor
CTF-6
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Ultra compact size and high accurate output linearity.*Easy installation in the distributing box.*Compliant with RoHS drective.
-
Product
Shunt: ACQ-200
BWR
-
*5 watts*Resistance values down to 0.0003 ohms*Special tight tolerance are available on request
-
Product
High-Voltage Differential Probe, 100 MHz
N2790A
High Current Probe
Use the N2790A 100-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2790A probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 1,400 V of differential voltage and 1,000 V of common mode voltage.
-
Product
AC Relays
-
The E-MAX ATR and ACV Relays are the AC equivalents of the industry standard E-MAX TIR Trip Indication Relays and AVR Auxiliary Voltage Relays. While the TIR and AVR Relays are designed for use in DC trip circuits, the ATR and ACV are designed for use in AC trip circuits. The relay outputs may be used to record breaker, relay, communication and control system operations, and to activate alarm and/or annunciator contacts. Relays do not require standby power to operate; they are powered by their inputs.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-40SQ
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Low cost*AC 1mA～50A*High Sensitive and least affection from external magnetic field
-
Product
Precision Power Shunt Resistors
PSS
-
*Resistance from 50uOhm to 1mOhms*Power Rating to 100Watt
-
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
Product
AC Power
-
At Transcat, our DC and AC power sources come with a broad scope of voltage and current ratings to meet your exact application requirements. We offer regulated and unregulated models that allow you to design AC-powered products and test electrical equipment accurately, across a wide range of input voltages. Our switchable power sources mean you can use one device to easily switch between AC and DC power for efficiency and accuracy in product testing. Brand such as Keysight, Eagle Eye Power Solutions, and B&K Precision lead the industry in manufacturing reliable AC Power Supplies.
-
Product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
-
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
Product
Shunt
-
Shunts are used with Moving Coil Ammeters for the measurement of current in DC Circuits.
-
Product
Current Transducer
IN 1000-S
-
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
Product
Current Transformer
ST-40CT
-
Standard Electric Works Co., Ltd
● 200/5A - 400/5A● 3-5V A● Class 1● Insulation 600V
-
Product
Mini AC Leakage Current Clamp Tester (CE)
M-140
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*40mmφCT window and ultra compact size.*Least affection from the external magnetic field.*Wide current measurements.(AC0.01mA-300A)
-
Product
Current Detectors
-
On our website you will find current detectors that are ideal for measuring AC or DC voltage. Current detectors are irreplaceable for inspection work and maintenance. We offer the following: voltage detectors, voltage leak detectors, voltage power detectors, Current clamps ideal for measuring AC or DC voltage. metric detectors, current detectors and more. These high quality current detectors include the capacity to measure many other parameters, such as capacity, resistance, power (both by way of clamps or by means of a hand held digital device with external clamps with a range of one or three stages). The current detectors are like the majority of our measurement instruments in that they meet and excel ISO standards. This calibration is done in a laboratory and comes with an accompanying certificate. All of our current detectors can perform the demanding tasks in each industrial sector regardless of the technical problem you encounter. If you can't find the current detectors you are looking for, please contact us and we will help you find the best solution to suit your needs by calling our offices on: UK customers +44(0) 23 809 870 30 / US customers (561) 320-9162 and our technical staff will advise you regarding our measuring instruments. Our engineers and technicians will be happy to help you with the current
-
Product
AC Ionisation
AC Long Range
-
Fraser Anti-Static Techniques Ltd
Produces a fast, quiet, flat jet of ionised air for efficient static neutralisation and cleaning.
-
Product
Current Mirrors
-
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
Product
Current Booster
PHPC01
-
PHPC01 current booster is an accessory which can work together with protection relay test kit to test transformer protection relay testing. It is specifically designed to supply high compliance voltage even at small current range.
-
Product
Through Hole type AC Current Sensor
CT-6S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Current Sensors and AC Current Sensors
-
Current sensors are designed to monitor the presence or absence of AC or DC current and are available in an assortment of standard & custom models with hermetic or gasket seal models designed to withstand severe environmental conditions.
-
Product
Shunts
-
Highly accurate manganin resistance d.c shunts. When a current is passed through the shunt a proportional millivolt output is produced.
