Line Replaceable Unit
unit of a complex engineered system, designed for quick replacement.
See Also: LRU
-
Product
Motor Termination Units
-
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
Emergency Power Supply Units (EPSU) (24) 5-20R 0U V
EPS-2420-V60
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
Test Fixture
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
Classic Collet | Black | With Line | Matt Or Glossy | Ø 28 Mm
021-5x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
Advanced Line Protection System
ALPS
-
ALPS is a multi-function digital protective relay system intended toprovide distance protection for HV or EHV transmission lines. It maybe applied on or adjacent to series compensated lines. It is availablefor single or three phase tripping applications. Typical operatingtimes are to 1 cycle.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Caraya Unit Tester
-
Caraya is a new experimental open source assertion and unit testing framework for LabVIEW. It takes a whole new approach to unit testing; your VI is your test. Caraya allows you to convert your manual test VIs you use for debugging into unit test cases with nearly no effort. Even running the tests is easy, just run the test case VI. Caraya significantly lowers the barrier for developers to write unit tests leading into improved overall code quality in real-world projects where developers don’t always have the luxury to write unit test cases first.
-
Product
Speaker/Receiver Unit Tester
BK2120A
-
Our new, upgraded BK2120A is a complete system for testing both acoustical features and rub & buzz in microspeakers, receivers and earphones or earbuds. It is just as fast and easy to use as our "Classic" BK2120A speaker tester, but because it connects with a LAN cable, you can use it with a notebook, as well as a PC. Its new modular design also makes maintenance more convenient and the redesigned BS1123 software is even easier to use and more versitile than the old version. You still get both graphical and numeric test data but with more display options than before. We still customize our machine to your special needs and of course you can still save your data to analyze later. Easier setup, improved design, more features, easier to use: we expect our new BK2120A to be even more popular than the original!
-
Product
Discharge Units
-
ENTES Discharge Units are used in capacitor banks and provide quick discharge over short periods of time.
-
Product
Multichannel Source Measurement Unit
AXS7720
-
Extremely low noise with linear output stageVery fast rise and fall timesProgrammable current pulseIntegrated current measurement unitIntegrated voltage measurement unit
-
Product
Replacement Protective Cover, I1, Receiver
310113524
Protective Cover
The receiver protective cover is designed to protect your modules and contacts while the test system is not in use. A protective cover is included with the i1 Receiver.
-
Product
Standard 1.00 (28.00) - 2.30 (65.00) Non Replaceable General Purpose Probe
P2532-2
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 156Test Center (mm): 3.96Full Travel (mil): 139Full Travel (mm): 3.53Recommended Travel (mil): 93Recommended Travel (mm): 2.36Overall Length (mil): 812Overall Length (mm): 20.62Rec. Mounting Hole Size (mil): 94.5Rec. Mounting Hole Size (mm): 2.40Recommended Drill Size: #41 or 2.40 mm
-
Product
Absorber Lined Shielding Enclosure Measurements
ALSE
-
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
Product
1RU Automated Switch Unit
UC1
-
Universal Switching Corporation
The UC1 switch system provides a modular solution for a variety of signals up to 50GHz, and is designed for smaller requirements. This product delivers ultra-high signal performance coupled with advanced remote/manual control and monitoring with 10/100 LXI certified Ethernet port, multi-serial port, front panel control, direct alarm input port, and auto-sense (on some PUC's).
-
Product
LXI WTB Adaptor, Thru line
60-982-001
-
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Product
Party Line Intercom Conversion
COMMS Series
-
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7205A
Attenuator
The J7205A is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to5 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205A reduces cost of ownership and provide the best measurement accuracy.
-
Product
Precision Source/Measure Unit, 1 Ch, 10 FA Resolution, 210 V, 1.5 A
B2910BL
Source Measure Unit
The Keysight B2910BL Precision Source / Measure Unit (SMU) is a 1-channel, compact and cost-effective bench-top SMU with the capability to source and measure both voltage and current. It is versatile to perform I/V (current vs. voltage) measurement easily with high accuracy. Integration of 4 quadrant source and measurement capabilities enables I/V measurement simply and easily without configuring multiple instruments.
-
Product
Classic Collet | Black | With Line | Matt Or Glossy | Ø 9 Mm
021-1x20/5
-
Secure plastic mounting cap for collet or wing knob
-
Product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
AFU 300 Auto Feather Unit
-
The Autofeather Unit (AFU), is mounted on the engine’s un-pressurized engine compartment, provides torque signal conditioning, automatic propeller feathering and remote engine uptrim command for Take-Off operations, as well as engine output torque indication to the aircraft cockpit during all engine operating conditions.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
21-Ch 6A-250VA 2-Bus Fault Insertion
YAV90077
Fault Insertion Unit
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Dual Output AWGN Generator Line Module
458-AWGN2
-
The Model 458-AWGN2 is the ideal solution for injecting Additive White Gaussian Noise (AWGN) for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing applications.
-
Product
Telephone Line, PCM and Other Copper Wire Tester
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Tel Line, PCM and Other Copper Wire Tester is developed for the fault testing of local telephone circuit using internationally advanced measuring technique in connection with the current situation of domestic telephone network. The instrument is of portable structure, and specially designed for the use of telecom and exchanger room operating staffs, line attendants, mobile phone servicing staffs and etc.
-
Product
625 KHz Data Acquisition Multifunction (Analog Output X2 Lines) PCMCIA
DAQi616MF(MF236/i)
-
The DAQi616MF is a type II PCMCIA I/O card for notebooks and other computers containing a PCMCIA slot.
-
Product
Pulse Heat Unit (Hot Bar Bonder)
-
*This method is most suitable for reliable soldering and thermo-compression because heating and cooling are done applying the pressure force*Good repeatability of heating temperature and time requires no skilled workers*Partial heating in short time allows to reduce thermal damages*For implement of Pb free
-
Product
Analyzer for Safety Agency Production Line Testing
HypotULTRAIII
-
Ethernet Communication CardUSB/RS-232, GPIB & Printer InterfacesData Storage CardInterconnection to Modular Scanning MatrixOptional 10 Volt Analog InterfaceStorage of up to 50 setups with 30 steps per setupPatented SmartGFI® functionPatented prompt and hold functionPatented CAL-ALERT® functionPatented VERI-CHEK® functionReal Current measurementDual Continuity test modesBuilt-in security settingsLine and Load regulation
