PXI DAQ
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-253-010
-
The 40-253-010 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 3.55kΩ
40-253-023
-
The 40-253-023 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 12-Slot BRIC Matrix, 840x6 1-Pole (10 Sub-cards)
40-558-121-840X6
-
The 40-558-121-840x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 66x16 1-Pole (6 sub-cards)
40-562A-021-66X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2 Amp Multiplexer, 8-Bank, 8-Channel, 1-Pole
40-657A-001-8/8/1
-
The 40-657A-001-8/8/1 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785585-01
-
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
PXI 2A Multiplexer, 16-Bank, 8-Channel, 1-Pole
40-614B-001
-
This 16-bank, 8-channel, 1-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 8-Slot BRIC Matrix, 121x16 1-Pole (11 sub-cards)
40-562B-121-121X16
-
The 40-562B-121-121X16 is a high density BRIC8 matrix module with a size of 121x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Density Multiplexer, 20-Bank, 8-Channel, 1-Pole
40-615A-001
-
The 40-615A-001 is a 20-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single SP6T MUX 6GHz 50Ω SMA
40-784-001
-
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI 2x DPST Power Relay, 2 Slot
40-170-002
-
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-134-HI
-
The 40-230-134-HI (PXI) and 42-230-134-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-136-HI
-
The 40-230-136-HI (PXI) and 42-230-136-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Single Microwave SPDT Relay 26.5GHz 50 SMA
40-780A-531
-
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options)
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-02
-
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
PXI High Voltage Programmable Resistor Module, 1-Channel, REDEL Connector
40-230-345-HI
-
The 40-230-345-HI (PXI) and 42-230-345-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
-
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
PXI 8-slot BRIC Power Multiplexer, 2-Channel, 48-Pole (4 Sub-cards)
40-571A-002
-
The 40-571A-002 is a 2-channel, 48-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI FPGA Module for FlexRIO
-
PXI FPGA Modules for FlexRIO offer up to 132 singleended I/O lines configurable as 66 differential pairs as well as large onboard FPGAs for signal processing. You can pair the module with FlexRIO adapter modules that offer highperformance analog and digital I/O. Together, the two modules create a reconfigurable instrument.
-
Product
PXI Remote Mount Dual SP6T Multiplexer 50GHz 50, SMA-2.4
40-785B-552-E
-
The 40-785B-552-E is a remote mount dual 6-channel 50GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 4 Slot BRIC 15x32 1-Pole (3 sub-cards)
40-562A-021-15X32
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Single 8 Channel Optic Mux FC/PC
40-852-118
-
The 40-852-118 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
8-Slot BRIC, 126x12, 1 Pole, PXI Matrix (3 Sub-cards)
40-559-801-126x12
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXIe-4340, PXI Displacement Input Module
785068-01
-
The PXI Displacement Input Module supports 4-, 5-, and 6-wire AC linear variable differential transformer (LVDT) and AC rotary variable differential transformer (RVDT) measurements. The module simultaneously samples each analog input and sets the excitation frequency and voltage for each channel independently. You can set different timing, triggering, and sampling modes for each channel independently. Diagnostic features include self-calibration, overcurrent detection, and open coil detection.The PXI Displacement Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
PXI 32x6 Matrix Module, 1-pole 2A 60W
40-506-001
-
The 40-505/506/507/508/509 are a range of medium density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 8-slot BRIC Matrix, 84x12, 1 pole (2 Sub-cards)
40-558-801-84x12
-
The 40-558-801-84x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8-slot BRIC Multiplexer, 6-Channel, 80-Pole (5 Sub-cards)
40-570A-113
-
The 40-570A-113 is a 6-channel, 80-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
8-Slot BRIC, 384x4, 1 pole, PXI Matrix (3 Sub-cards)
40-559-801-384x4
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
