Isolated Digital Output Modules
-
Product
PCIe Thunderbolt 3 EON Express 12-Bit Digitizers
Thunderbolt 3
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
PCIe Oscar Express 16-Bit Digitizer
Digitizer
The GaGe Oscar Express 44XX CompuScope PCIe digitizer board features 16-bit resolution with sampling rates up to 100 MS/s with true Effective Number of Bits (ENOB) of 12.2-bits with 10 MHz input.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5922-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
Digital Module
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
Product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Analog Output Module For Remote I/O
Analog Output Module
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PXIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4X.4481-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4I.2234-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
80 I/O Multifunction Module
YAV90832
Digital I/O Module
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI I/O Board
MZ-TrigIO
Digital I/O Module
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
Product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5942-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PXIe-5622 , 150 MS/s, 16-Bit PXI IF Digitizer
780412-02
IF Digitizer
150 MS/s, 16-Bit PXI IF Digitizer—The PXIe‑5622 includes onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real DDC, and anti-alias filtering. The PXIe‑5622 is ideal for communications applications because of its high dynamic range front end and a high-throughput PXI Express interface that allows it to stream IF data to disk for hours at the full sample rate.
-
Product
16 / 180 MS/s Bit Waveform Digitizer
WFD16
Waveform Digitizer
The WFD16 is a 16 bit Waveform Digitizer for high-speed / high resolution waveform capturing and analyzing. The fully differential signal path ensures an exceptional high signal quality. Despite this emphasis on signal quality the WFD16 also has a good DC accuracy. The module features differential inputs with a 50 Ohm or 10 kOhm termination and a with a programmable common-mode voltage.
-
Product
Thunderbolt 3 RazorMax Express 16-Bit Digitizers
TB3 – RazorMax
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5050
Digital I/O Module
The GX5050 is a high speed Dynamic Digital I/O card that provides a full set of features that is comparable to high speed I/O products found in large functional test systems. The card shares an identical architecture with the GC5050, but the GX5050 is a PXI card (6U) and the GC5050 is a PCI card. Both have the ability to operate independently of the host computer when in RUN mode.
-
Product
PXI-4072, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter
778270-01
Digital Multimeter
6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter - The PXI‑4072 is a high-performance 6½‑digit, 300 V DMM that provides the measurement capabilities found in two common test instruments: a high-resolution DMM and a digitizer. As a DMM, the PXI‑4072 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, frequency, period, and basic L and C measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXI‑4072 can acquire waveforms at sample rates up to 1.8
-
Product
RF Digitizer With 6.5 GHz Bandwidth
ADQ7WB
Digitizer
ADQ7WB is an RF digitizer with an analog input bandwidth of 6.5 GHz. It supports highly linear wideband data capture, and utilize Teledyne SP Devices' proprietary ADX technology in order to ensure industry-leading spurious-free dynamic range (SFDR).
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 2 DAQ Channels and 2 AWG Channels
DN2.813-02
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
1.6 GSPS, 14-bit Time-domain Digitizer
ADQ1600TD
Digitizer
The ADQ1600TD is a world-leading 14 bit digitizer optimized for time-domain pulse capture. With its unique 1600 MSPS capture rate, enabled by SP Devices’ ADC interleaving technology ADX, the ADQ1600TD opens for demanding measurements such as time-domain pulse capture and high-speed data recording.
-
Product
PXI Digital Pattern Instrument
Digital Pattern
The PXI Digital Pattern Instrument is designed for semiconductor characterization and production test. It provides 32 channels, a voltage range of -2 V to 6 V, a PPMU force voltage range of -2 V to 7 V, up to a 200 Mb/s data rate, and a clock generation rate up to 160 MHz. The module includes Digital Pattern Editor software as well as debugging tools like shmoo, digital scope, viewers for history RAM, pin states, and system status.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/S External State Clock
M4I.7720-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
Software Abstraction for Easy Control of Digital Multimeters & Multifunction Measurement Devices
DMM
Digital Multimeter
It consists of three modules:- A windows driver which is responsible for the communication and device abstraction- A DLL with NI TestStand Test Steps which allows easy integration in automated production enironments- A standalone executable which simplifies debugging and setup of test sequencesThis architecture allows to open a communication channel from multiple instances to the same device. This is important when for example two channels of a measurement device are used in two independent applications.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785960-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer.
-
Product
Nano-Volt/Micro-Ohm Meter, 7.5 Digit
34420A
Digital Multimeter
The Keysight 34420A nanoVolt, micro-Ohm meter is a high-sensitivity multimeter optimized for performing low-level measurements. It combines low-noise voltage measurements with resistance and temperature functions, setting a new standard in low-level flexibility and performance.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
Digital I/O Module
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
Digital I/O Module
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
