Filters
Electronic circuits which refine signal by blocking certain frequencies, while allowing other frequencies to pass.
See Also: Filter / Amplifiers, EMI Filters, Low Pass Filters, Programmable Filters, Attenuators
-
product
IP Parallel HV
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
product
Automation
Signal Filtration
Signal Filtration is used for filtering signals coming to the input channels of spectrum analyzers, strain-gauge stations, and seismic stations, for further processing by ZETLAB programs. Signal Filtration can also be used for processing virtual channels created by such programs as Vibration Meter, Strain-Gauge Sensor, etc. Signal Filtration operates with signals both in real time and with reproduced of recorded signals.
-
product
Power Supplies
CF - SERIES
The CF-series power supply is built with high-quality components for extra long life and maximum system performance along with heavy duty transformers supporting high-end systems. This fanless power supply has a built-in EMI filter for a true no-noise design. The aluminum chassis is built for maximum heat relief to keep the system cool. Combined with a great ventilated structure, you’ll never need a fan. This is a true silent structure that powers your system at 480 watts efficiency.
-
product
Pressure Measurement Accessories
Pressure subbers, connector bushings, grommets, pipe and tube fittings, tube by length, pressure cooling element, pressure and force cables and connectors, air line lubricators, and air filters.
-
product
High-Current, Ultra-Low Noise Filter, 21 V / 500 MA, 10 Ω
N1298A
The N1298A Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
product
Super-Notch YIG Band-Reject Filters
YIG Tuned BRF patented technology gets closer to the ‘perfect notch'. Leveraging a long heritage of engineering innovation in YIG technologies, Teledyne RF & Microwave has developed a line of YIG Tuned Band-Reject Filters powered by patented new technology that overcomes many long-time design limitations inherent to YIG Band-Reject or “notch” filters. Our new line delivers major advancements and unequalled performance.
-
product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Measurement System
MS-500 series
The MS series is suitable for pre-processing analog signals.The plug-in units of filters, differential amplifiers, isolation amplifiers, etc. can be installed into their frames.(16 channels at maximum/the JIS rack size)
-
product
Quiet Safety 4U Rack Mounted Industrial Chassis With 14-Slot Backplane And Motherboard
RK-620 Series
- EIA RS-310C 19” rack mount standard- Supports 14-slot backplane and ATX motherboard- Two 5.25” external, one 3.5” external and one 3.5” internal drive bay- Two USB ports inside front I/O- Replaceable, easy-to-clean air filter- PS2 ATX power supply- Low noise 12cm PWM controlled (103 CFM)
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
product
RFoG 4-Band Multiplexer. 1550, 1590 & 1310/1490nm MWDM
WD5943
Hangzhou Huatai Optic Tech. Co., Ltd.
WD5943 WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to FTTx PON network to achieve the combination and separation of the 1550nm (CATV) and 1310/1490nm (data).
-
product
PXIe-4300, 16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module
781337-01
16-Bit, 8-Channel, 250 kS/s, 300 V, Ch-Ch Isolated PXI Analog Input Module—The PXIe‑4300 provides integrated data acquisition and signal conditioning for high-voltage measurements. It provides increased accuracy, simultaneous sampling, and synchronization features for scalable measurement systems. The PXIe‑4300 includes 300 Vrms channel‑to‑channel CAT II isolation and 3,300 Vrms channel‑to‑earth 5 second withstand isolation to protect users and equipment from hazardous voltages. This module offers programmable lowpass filtering, DC input coupling, and two PFI lines for digital input triggering. The included NI‑DAQmx driver simplifies hardware and configuration and measurement.
-
product
Power Supplies
CF-400B
The CF-series power supply is built with high-quality components for extra long life and maximum system performance along with heavy duty transformers supporting high-end systems. This fanless power supply has a built-in EMI filter for a true no-noise design. The aluminum chassis is built for maximum heat relief to keep the system cool. Combined with a great ventilated structure, you’ll never need a fan. This is a true silent structure that powers your system at 480 watts efficiency.
-
product
Varactor Tuning Diodes
Macom Technology Solutions Holdings Inc.
MACOM’s GaAs and Silicon varactor tuning diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for high Q filter and VCO electronic tuning circuits and are available in die form, flip chip, plastic and ceramic packaging. These GaAs diodes boast a constant gamma series for higher frequency and high Q applications and silicon abrupt and hyper abrupt series in plastic packaging are suitable for high volume surface mount applications.
-
product
PXIe-5113, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope
786405-11
PXIe, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5113 oscilloscope has two channels that sample up to 3 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 500 MHz of analog bandwidth.
-
product
Automatic Battery with Filters with Standard Contactors
BATLVF120
Lifasa - International Capacitors, SA
Accessories: Differential protection
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.442-20
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
USB Smart Detector
OL 731
The OL 731 USB Smart Detector is a low-cost, hand-held radiometer/photometer that can be tailored to the spectral response of the user's specific application requirements with the use of a range of sensors and filters. Several units can be multiplexed on to one USB, and it can be programmed to read in any user-specified radiometric or photometric unit. The OL 731 is suitable for a variety of critical applications.
-
product
Radiant Imaging Tester
Lumere-ZeM
Evolusys Technologies Sdn. Bhd.
• CIE matched color filters and neutral density filters• Wide range of working distances and aperture settings• Color and light measurements
-
product
PXI-5152, 300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope
779772-01
300 MHz, 2 GS/s, 8-Bit PXI Oscilloscope—The PXI‑5152 high-speed PXI oscilloscope has two channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations. The PXI‑5152 also features PXI synchronization and data streaming capabilities.
-
product
Semiconductor Yield Management Software
QuickLoad-Central
QuickLoad-Central is our new STDF filtering, analysis, reporting, managing, viewing and editing tool. It looks at all your STDF files before you need to, pulling out key information to pre-generate reports and help you quickly find the files you need. You can list files of interest with yield and header information on our dashboard, visualize your data, open pre-generated reports or push any information from them that you can think of to JMP, Excel or other analysis tools.
-
product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
product
PDS Multibeam Survey and Processing/Charting
Teledyne PDS for Multibeam Surveys provides the functionality for survey planning, data acquisition, data processing, editing, volume calculations and chart production. This turnkey solution offers the surveyor and helmsman a strong tool to carry out the multibeam survey efficiently. Progress is shown real time in top, profile, and 3D views using a color-coded digital terrain model (DTM). Various filter settings can be applied to the multibeam data online, thus providing real-time data processing. Quality control displays reassure the operators that the data is of the desired quality.
-
product
CompactPCI
CPCI-ADDA
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-4
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz*14-bit resolution*Output voltage: 0-10 V, ±10 V, (set through software)*Each output has its own ground line*Driver capacity: 5 mA/500 pF*Short-circuit protection: EMI filters*Data exchange through 16-bit I/O digital*4 digital inputs*and 4 digital outputs, 24 V , opto-isolated
-
product
Low Noise Filter Adapter
PX0107A
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
