Test Bench
worktable including instrumentation, fixturing and unit under test.
See Also: Test Benches
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Hydraulic Data Logger
HPM7000
-
The HPM7000 series, is a highly versatile portable hydraulic data logger and the evolution of the HPM6000. It is ideal for diagnostic testing of hydraulic systems, use on hydraulic test benches, pre-dispatch inspection or for Research and Development (R&D). There are a variety of different data logging modes with the ability to data log up to 16 million measured values per test at a variable interval from 1 ms, with a total possible storage size of 12GB (approx. 250 measurements).
-
Product
Test Benches DC
-
Combined with a power source system e.g. MTS750 this test bench is used as a DC meter test system with 40 test positions.
-
Product
Testing Wiper Motors
-
Magtrol developed two automatic testing benches for front wiper motors, rear wiper motors (pendulum with measure of angle) and ABS motors (excenter). The test setup is equipped to handle torque ratings from 3 to 50 Nm and a speed range of 0 to 10,000 rpm
-
Product
Speedometer Test Bench
-
Maschinenbau Haldenwang GmbH & Co. KG.
Tachometer tester for cars and commercial vehicles.
-
Product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Calibration Test Benches
-
Nagman Instruments & Electronics Pvt. Ltd
Nagman’s wide range of Calibration Systems – Test Benches, Workstations, Bench-tops & Mobile Units – are designed & executed to serve as Powerful tools for Total Quality Management & ISO Conformance with Accuracies Traceable to International Standards and Total Solution to all Calibration requirements.
-
Product
Custom Bench Test
-
TestEdge provides customized bench test. If your device has specialized test requirements, it may be necessary to test your device using specialized bench equipment rather than traditional ATE. In other situations, both ATE and a custom bench setup may be required to fully characterize the device and provide necessary correlation. Finally, it may be useful to create a custom bench setup to facilitate device debug.
-
Product
Automated Measuring System
-
The Ford Meter Box Company, Inc.
Accurate test results● Easily interface meter test data with your computer network● Security device provides a secure internet connection with Ford Meter Box● Touch-screen PC provides step-by-step instructions● Test bench is available in single or double row● Performs tests without constant supervision● Optional remote operation (not supplied by Ford)● Tests high, intermediate and low flows● Preprogrammed tests or customized tests
-
Product
Axle Damping Test Bench
C_MSD C 2.5 W220 | VP 215047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
Product
Integrated Test Facility
ITF
-
The ITF, located in El Segundo, California, has multiple test stations to enable parallel testing and significantly streamline program test schedules. More than 25,000 square feet are available for integration and test activities, including a 10,000-square-foot Class 10K clean room. Our facilities feature thermal vacuum chambers and test stations to support optical alignment, warm optical bench testing, and hardware integration.
-
Product
High Voltage Safe Measurement Systems
-
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
Product
Atec Series 7
-
TEC® Series generic purpose test benches are used by most airlines, systems manufacturers and MROs (Maintenance, Repair and Overhaul) companies to guarantee the conformity of critical electronic equipment. Available on all continents, the ATEC® Series can be adapted to suit various needs owing to its modular nature and capacity to test almost all airliner LRUs. SPHEREA has the world’s largest testing library.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY8125
-
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. ● The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception.● The device has the features of high stability, good reliability and large output power. ● High level of autoimmunization. The coexistence of special small keyboard and PCs, convenience to use.
-
Product
Testing of Compressors and Compressors
-
Automatic production test bench for semi-hermetic refrigeration compressors on 2 parallel assembly lines with 3 test stations each and central database.
-
Product
Atec Dyna
-
Macro-instruments an innovative concept : ultra-simple interface between the test bench and the equipment being tested, Software-controlled macro-instrument, Generic TUA (Test Unit Adapter) incorporated in the bench
-
Product
Single Phase Energy Meter Test Bench Type KP-S1000-A
-
Bofa Instrument & Equipment Co., Ltd
Single phase test bench, type KP-S1000-A, is a new generation, high precision energy meter calibration equipment. It can test mechanical energy meter and electronic energy meter, in spite of open or closed test link (I-P link). It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
Precision DC Power Module, 20V, 50A, 300W
N6763A
Power Module
The Keysight N6763A is a 300W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB and LXI compliance are standard. Select from more than 30 different DC power modules ranging in capability from basic to high precision, and in power from 20-500 Watts.
-
Product
Four Position Meter Test Bench
TB41
-
Calmet Smart Calibration Devices
The Calmet TB41 Four Position Meter Test Bench is used for calibration and simultaneously testing up to four single and three phase electromechanical and electronic acitve and reactive electricity meters with accuracy referenced to an internal reference meter (class 0.02% or 0.04%).
-
Product
Customization & Automation
-
For production and test bench applications, the operation of the measurement needs to be either semi or fully automated. On top of its turnkey solutions, Oros offers a large number of tools to open the programming access. This can be addressed based on all levels of programming expertise achieved by OROS users themselves, local partners or OROS teams.
-
Product
Pitot Static Indicator
ADSE 740
-
The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
GoldenGate RFIC Simulation Software
-
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
Product
RF Channel Simulators
-
Kratos Defense & Security Solutions, Inc.
The T400CS creates RF and/or IF signals that precisely match those that occur when transmitters and receivers are in motion with respect to one another. By accurately duplicating the motion effects and RF channel physics effects on an RF link, the T400CS allows bench testing of what once required actual motion and distance between a transmitter and receiver.
-
Product
DC Power Module, 20V, 2.5A, 50W
N6733B
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
Test Operator Platform
TOP
-
TOP/TRM provide a multi user test run management for your system test bench: Comfortably create tests, run test batches and review results. The execution queue schedules all tests and also allows prioritized single user access.
-
Product
Analog/Linear Tester
Amoeba 4200
-
4200 is capable of running multiple test sites independently with a parallel efficiency of up to 85% for quad-site and octal-site testing.It comes with test development and production software suite, which makes the transition from test development and bench characterization to production seamlessly.
