Mixed Signal Testers
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, MIxed Signal Test Systems
-
product
Signal Analysis
Cross-Spectrum FFT Analysis
The program Cross narrow-band spectrum is used for evaluation of the interrelation between the signals’ parameters obtained from the two primary transducers installed at various parts of the controlled object. This program can be used for detection of noise source location, for sound absorption level evaluation and the researched object acoustic properties control, for evaluation of space-time distribution of the directional energy flux (Poynting vector), for the ground cross-section FR characteristic evaluation (Nakamura method), etc.
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
SIGnal Workbench
Flexible, programmable signal conditioning and fault insertion solutions for data acquisition applications.
-
product
Signal Generator
8003
5 digit BCD, 1 latch control line, 25 pin female, D type connector. May take several minutes to achieve for the largest frequency steps. Normal switching mode, SSB phase noise will be degraded in the fast mode.
-
product
Mixed Signal Oscilloscope - 200 MHz, 4 Analog Plus 16 Digital Channels
MSOX3024T
200 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
Mixed Signal Oscilloscope, 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012A
100 MHz2 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-02
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
"Signal Transporter"
LTX-5525
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
product
Signal Interface
Our signal interface products provide signal conversion and electrical isolation between sensors and other field devices and a control circuit. Intrinsic safety modules add Zener diodes, which limit the amount of electrical energy on intrinsically safe circuits.
-
product
"Signal Transporter"
LTX-5520
The LTX-5520 enables the conveyance of sixteen independent channels of digital information over fibre optic links ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled at 50 mega-samples per second, multiplexed and transmitted serially over an optical fibre at a 1 Gb/s data rate.
-
product
Mixed Protocol Modules
The ANET-MxAy offers mixed protocol support, combining MIL-STD-1553 and ARINC429 data bus test and simulation capabilities in one ANET device.
-
product
Signal Amplifier
ZET 412
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
product
Mixed Signal Oscilloscope, 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014A
100 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWG
610110147
Signal, Contact, ITA, TriPaddle, 10 Amp, 14 AWGThis contact primarily used in CASS applications.Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation Compliant
-
product
Signal Amplifier
9200
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Signal Generators
NF‘s function generators have been used in many applications, since NF produced the first Japan-built function generator in 1959.A function generator is general-purpose test equipment used to generate various waveforms and to execute trigger, sweep and gate oscillation.
-
product
Video Signal Distributor
MSHD-02
MSHD-02 distribute inputted component signal to the two (2) output channels via RCA connectors without diminuation & distortion. It takes High Bandwidth Video Distributor IC which is support the highest component resolution up to 1920X1080P & Dot Clock 148.5MHz.
-
product
RF Signal Amplifiers
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
product
Video Signal Distributor
MSVD-250N
MSVD-250N is a Analog Distributor Buffer that distribute one (1) input signal to the 5/10/15/20 channels. User can select input type between 15P D-Sub and 5 BNC (R,G,B,HS,VS). The distribution buffer can be used in factory assembly lines, repair depots, and for system integration to save cost and time.
-
product
NI-5742, 16-Bit, 1 MS/s, 32-Channel Signal Generator Adapter Module for FlexRIO
782865-01
The NI‑5742 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5742 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5742, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
product
Signal Analysis
STA/LTA Detector
The STA/LTA Detector program is a representation of a detector of various events in triaxial or single-component time signals. The software is based on one of the STA/LTA detector types.
-
product
Signal Path Analyzers
HL5200 Series
HYPERLABS HL5200 Series Signal Path Analyzers™ provide ESD-robust, multi-channel test and measurement capabilities for a fraction of the cost of traditional benchtop systems. These differential instruments have up to 20 channels and can be used to take TDR, TDT, and XT (crosstalk) measurements. Beginning in June 2015, S-parameter (S11/S21) data will also be available.
-
product
Video Signal Distributor
MSHD-10N
MSHD-10N distribute received one(1) D-TV(Y,Pb, Pr) and audio(R,L) signal to the ten(10) channels. It is recommended reliable test room and show room.
-
product
Mixed Signal Oscilloscope 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032G
The MSOX3032G 350 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
product
Quadrature Signal Generator
TE5100-PCI
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
product
Signal Management Solutions
QUBE Series
The QUBE Series is an expanding line up of signal management solutions that are housed in the same enclosure as the popular VB-10 line of fiber optic transport products. The QUBE Series offers a rugged standalone form-factor providing 12G-SDI failover and distribution as well as routing. The QUBE Series and VB-10 Series products can be racked together to provide unique optical transport and signal distribution systems.
-
product
Signaling Gateway Solutions
Service Providers are making the transition to 4G, and 5G is coming, but legacy connectivity for voice, SMS and IN applications still remains an absolute requirement. SS7 TDM interfaces must be maintained to meet the demand to interconnect different networks and multi-protocol solutions are required to connect divergent circuit and packet switching architectures. SS7 isn’t retrograde – it’s traditional. It’s still the most robust, high performance, and reliable signaling solution out there and it’s needed today more than ever.
-
product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX4032A
350 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
product
Video Signal Generator
MSPG-925FU
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneously and sufficiently examining a large size display device.
