DVB-T2
Digital Video Broadcasting – Second Generation Terrestrial
-
Product
ARINC 818 Recorder
-
ARINC 818 Digital Video Recorder powered by Xilinx Zynq Ultrascale+ MPSoC device, is a multi-channel record/playback system that accepts any form of ARINC 818 video input with different resolution & refresh rates. The received ARINC 818 video stream is encoded with the assist of an on-chip H.264/H.265 video codec engine which is capable of performing simultaneous compression and decompression of video streams. Finally, the encoded video is stored in SSD hard drive.
-
Product
High Power/Anti-Surge/High-Voltage Resistors
ERJ-P Series
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s ERJ-P Series High Power Resistors offer the ability to use smaller case sizes while still maintaining the same level of power or better in respect to conventional size Thick Film Resistors. The ERJ-P Series has a unique trimming pattern and high heat dissipation characteristics. These parts can be easily designed as replacements for existing Thick Film Resistors due to comparable technology and materials with use of better manufacturing processes. The ERJ-P Series has an operating temperature of -55°C to 155°C, with a smaller part, you have a higher solder-joint reliability. Less material means less solder which lowers risk for solder fracture due to thermal expansion or contraction. Panasonic High Power Resistors are AEC-Q200 Qualified.
-
Product
Tool, Locator, TriPaddle, Receiver
910104146
Locator Tool
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
Product
Bridge Rectifier Diodes
-
ST’s portfolio of bridge rectifier diodes is intended for primary bridges. In input primary bridge applications, ST's 1200V bridge diodes achieve very low conduction losses thanks to very low forward voltage characteristics. They can operate at up to +175 °C junction temperature, as a result of reduced leakage currents. Bridge rectifier diodes are belonging to the STPOWER family.
-
Product
Code Coverage Branch Monitor
CCBM
-
Verified Systems International GMBH
The Code Coverage Branch Monitor (CCBM) is a set of utilities that allow instrumentation of C source code for the purpose of branch coverage measurement. This encompasses operations for code instrumentation, removal of this instrumentation, retrieval of coverage information, merging coverage information, and displaying this information with reference to the (original) source code.
-
Product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Interface
RPCIE-1553
Interface
Abaco Systems RPCIE-1553 is the latest generation of performance and flexibility for MIL-STD-1553 A/B Notice II on a native PCI Express module. Available in -40°C to +70°C temperature with one, two or four dual-redundant channels, the RPCIE-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
McMurdo FastFind - Neck Lanyard
10-91-060-002A Fast Find 210
-
Standard model with GPS for extra fast position location Announcing the amazing new McMurdo FastFind Satellite Personal Locator Beacon (PLB): the most compact, waterproof and versatile 406 MHz emergency location beacon available on the market today.The Fast Find is a 406 MHz Personal Location Beacon (PLB) that should be carried by individuals, who are embarking on trips into areas around the world where there is little or no other forms of communication or where other forms of communication are unlikely to work. The Fast Find acts as your personal Emergency Location Beacon, it is your last resort communication to the national and international search and rescue bodies and it should not be misused. The Fast Find is designed as a direct communication, to the 406 MHz Search and Rescue satellite system, its signal indicates that you are in need of urgent response and assistance. The location of a McMurdo Fast Find 210 GPS PLB can be determine to a typical positional accuracy of about +/- 62 metres (0.03 miles) within a few minutes of PLB activation. McMurdo FastFind PLB Manual (.pdf)Its small size belies its rugged construction and powerful output. There is no compromise. Once activated, the distress beacon will send out a signal for help, and continues to transmit for at least 24 hours, at a powerful 5 watt output, ensuring that your call for help gets through whatever the conditions. The pocket sized beacon transmits at the press of a button, to alert search and rescue services to your plight.McMurdo FastFind PLB is an essential piece of life-saving equipment, weighing in at just 5.3 oz (150g) and having the size of an average mobile telephone (actual dimensions being 1.34”/34mm x 1.85”/47mm x L 4.17”/106mm) it will slip into the smallest pocket or backpack compartment. The user can activate it in the most remote locations around the world: on land, at sea or in the air, and can be confident of being able to contact the world’s professional search and rescue services directly if they are to encounter a possibly life-threatening situation.McMurdo FastFind PLB comes equipped with an integral 50-channel GPS system and complies with rigid federal and international standards. It operates on the global COSPAS SARSAT 406MHz search and rescue satellite communication system, so a call for help will be acted upon…and fast. The McMurdo FastFind PLB is subscription FREE and does not rely on any commercial call centers.THE McMurdo FastFind PLB model transmits two signals simultaneously: a global 406 MHz signal and a 121.5MHz local signal. Once activated, McMurdo FastFind PLB’s signals will continue to transmit for at least 24 hours, at a powerful 5 watt output, the 406 MHz transmission ensures that a call for help gets through, no matter what the conditions. McMurdo FastFind PLB also includes a unique flashing SOS LED light to further assist in speeding up the user’s recovery time during night rescues.McMurdo FastFind PLB will operate in temperatures as low as -20°c and its integral battery has a user storage life of 5 years, so there’s no need for frequent battery changes or re-charging.Put a McMurdo FastFind PLB in your pocket, and get found fast.
-
Product
High Temperature Transverse Extensometers (700 C)
Model 7675
-
Jinan Testing Equipment IE Corporation
Designed for transverse or diametral strain measurement in environmental chambers where the entire extensometer must be exposed to elevated temperatures. These capacitive extensometers may be used up to 700 C (1300 F) without any cooling.
-
Product
EtherCAT IO Slave For M-Type Modules
ECAT-IO M Series
-
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833x and SuperCAT master controllers, ECAT & EU slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK’s ECAT IO system features a modular design for flexible high channel density, rugged construction, easy maintenance, and compatibility with third-party EtherCAT master products. Precise time-deterministic control enables I/O synchronization for critical applications, while the flexible terminal block design supports multiple wiring methods. The ECAT’s unique structural and electronic design supports hot swapping of modules, reducing repair time, and offers full operability from 0°C to 60°C. The ECAT slave system is also fully compliant with the EN 61131-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as receiving an emission certificate.
-
Product
19" Drawer with Writing Surface, Unshielded, 8.75"H x 20"D
DR-081920-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Conductivity / TDS Monitor / Controllers
750 Series II Conductivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Conductivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
AC/DC Power Supply 20 W
CFM21S240-T
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 24 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety | JST connector
-
Product
48 Channel Relay Output Module
DP-VME-4059
-
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
Product
Solid State Active Synchro Control Differential Transmitter
-
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
-
Product
VME J2 12 slot
101VMEJ212-0900
-
VME J2 backplane 12 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
Product
300W - Single Output
i7C Series
-
*Wide 1/16th Brick Footprint*9-36 Vdc, 9-53 Vdc Input*5-28, 8-24, 9.6-48 Vdc Outputs*Non-Isolated Step Up/Step Down*-40 to 125 °C Operating Temperature*Openframe, Baseplate or Heatsink options*Trim, On/Off, Power Good, Sync, Imon
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
779012-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
784170-01
-
The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
Product
7 inch M-IPC-600C ip Camera Tester With 8MP HD-TVI, 8MP-CVI, 8MP AHD
M-IPC-600C
-
Fuzhou Metricu Technology Co Ltd
M-IPC-600C is 7 inch touch screen IP camera tester, that can test H.265 & H.264, 4K IP cameras as well as 8MP HD-TVI camera, 8MP HD-CVI camera, 8MP AHD camera, analog cameras, meanwhile it has PoE output, DC 12V 2A output, etc.
-
Product
Multi-Channel (Up to Four) MIL-STF-1760 Interface Board for Conduction Cooled PCI Mezzanine Card Compatible Computers
EXC-1553ccPMC/Px(S)-1760
-
The EXC-1553ccPMC/Px(S)-1760 is a multi-channel (up to four) MIL-STD-1760 interface board for conduction cooled PCI Mezzanine Card compatible computers. In addition, Checksum, SRQ bit and Header Words are supported on each channel. Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.Each dual redundant 1760 channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, error injection (BC and RT modes), error detection (all modes) and cableless internal loopback are supported on each channel. The EXC-1553ccPMC/Px(S)-1760 is supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
DCME Analysis System
-
DCME Analysis System (SCL-DAS) is a software based application, which is designed to classify, process and decompressed the compressed signals transmitted over the satellite links.DCME Analysis System supports most of the commercially available DCMEs including PCM, ADPCM, DX-3000, DX-7000, DTX-600, DTX-360, DTX-240 (D,E,F,T), CELTIC-3G, OKI TC-2000 etc. While processing the compressed/normal E1 carrier, the SCL-DAS provides the processed intelligible output in the form of Voice and Fax along with Originating Point Country, Destination Point Country, Outgoing Number, Incoming Number etc.
-
Product
Portable Interface Unit
1553-USB-PIU
-
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
Product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-01
Chassis
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
Dynamic Vapor Sorption Analyzer
IGAsorp-CT
-
The IGAsorp-CT is a fully automated dynamic vapor sorption analyzer for the measurement of water and organic solvent isotherms and kinetics on a wide range of materials. Operating at temperatures from 5 to 85 °C and humidity values from 0 to 98 %RH, the IGAsorp-CT offers the widest combined range of any DVS analyzer. An optional internal heater allows fully programmable pre-heating and thermal desorption measurements to 350 °C.
-
Product
32-CH ±10V Analog Input EtherCAT Module
EPS-3032
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
High-Voltage Test Device
PGK 150 / 5 HB
-
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
DVB-T2/T/C, ISDB-T And ASI Probe For USB-2
DTU-238
-
DekTec's USB-2 hardware-based receiver for DVB-T2, T, C2, C and ISDB-T. With full support for single- and multi-PLP, as well as SISO and MISO, this USB-2 probe is perfectly compliant to DVB-T2 v1.3.1.
-
Product
Silicon Based Thermopile Detector: 4 Channels
ST120 Quad
-
A four-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
