PICMG Backplane
-
Product
6-Slot Backplane Card Cage
IPC-6006
-
Open-frame card cadge for embedded system, Shockproof hold-down clamp design. Support 6-slots full size and half size SBC, Support one PS/2 power supply, one 3.5" HDD and one cooling fan.
-
Product
PCI Express, PCI, Multi-Interface Test Backplanes
-
Amfeltec PCI Express, PCI, Multi-Interface Test Backplanes
-
Product
3U 6-slots 25Gb Backplane Aligned To SOSA, Apertures For VITA 66/67 Modules
1SVX306AxP-xxxx
-
Designed in alignment SOSA, this 3U backplane offers 6 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
VPX Backplanes
-
Dawn’s VPX backplanes are based on Gen3 VPX, VPX (VITA46), VPX REDI (VITA48), OpenVPX (VITA65) and VITA 68 VPX compliance, available in a wide range of profiles and topologies.
-
Product
CompactPCI 3U Backplanes
-
COMTEL Electronics offer a large variety of CompactPCI 3U Backplanes, 2 – 14 slots 32 bit 33/66Mhz, fully compliancy with PICMG 2.0 Rev 3.0 Specs. & Hot Swap compliant per PICMG 2.1 R2.0 Spec.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB112
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
FlexVPX Backplane
-
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
Product
DIN Backplane
-
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
Product
High-Performance Gaming Platform with Backplane Architecture
ADi-SC2X
-
- High performance, high-end gaming platform with backplane architecture for easy maintenance- Superior, highly scalable CPU/GPU performance- Advanced security feature set and software solutions- Highly flexible system configurations that are fully in line with real project requirements- Lower costs: due to implementation of socket-type Intel® CPUs- Flexible maintenance and upgrade: slot-in machine construction, socket-type CPU support- Flexible maintenance and upgrade: slot-in machine construction, socket-type CPU support- Full-scale customization: GDDR5, V-BIOS, video ports, I/O ports, etc.- High integration: FPGA & logging controller onboard
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/6VP4
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX61222TP/AX61220TP*Supports ATX power supply*For 2U chassis
-
Product
Digital Backplanes
MSXB 034
-
Digital Backplanes provide expansion slots to accommodate compatible digital external boards. Digital Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical.
-
Product
Backplane Twinax Connectors
-
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
Product
Backplane & Cable Test
-
Backplane and cable test systems from Terotest include LINX, a fixtureless test system. Each LINX test card plugs directly into the unit under test, which removes the necessity for long test cables and fixtures. This is called distributed testing and results in dramatically lowered costs. LINX is extremely easy to use, with a self-learn function or input from CAD.
-
Product
DG I/O Backplane Extender Board
9286-1015
-
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
PICMG 1.3 Full-Size Single Board Computers
-
PICMG 1.3 Full-Size Single Board Computer (SBC), with multiple backplanes to achieve unrivaled flexibility and performance. Our Slot SBC with rich I/O interface and expansion slots also support Intel's latest processors.
-
Product
3U 12-slot VPX Backplane Aligned To SOSA 1.0
1OVX312AFQ-xxxx
-
3U 12-slot backplane with profiles aligned SOSA. It is designed to meet the U.S. Army’s C5ISR Modular Open Suite of Standards (CMOSS), and supports high-speed signals on all data paths and VITA 67.3 and VITA 66.5 connectors.
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
-
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
Product
1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E®x 4, 2 PCI™ Slots Backplane
EBP-D5E2
-
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 2 PCI™- Support ATX power supplies- Dimension: 331 mm x 84 mm
-
-
Product
3-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/3VP2
-
*1 PICMG, 2 PCI*Compatible with AX61120TP*Supports ATX power supply*For 1U chassis
-
Product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
-
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Product
Passive Backplanes
-
Passive Backplanes series are easily customized which include PCI boards, ISA boards, PICMG 1.3 full-sized, PICMG 1.0 full-sized and half-sized single board computers. All backplane products provide with matching chassis and outstanding expansion flexibility.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
13-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/13L
-
*1 PICMG, 4 PCI and 8 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
CompactPCI Serial 3U Backplanes / Power connector
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to the PICMG CPCI S.0 CompactPCI Serial specification. This backplane features 1 power slot in addition to either 6 or 9 cPCI serial slots.
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
-
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
6U And 7U VPX 1 To 15 Slot Power & Ground Only Backplanes
101VPX6xxP-xxxx
-
Elma’s 6U / 7U VPX power and ground only backplanes provide a cost-effective way to design and test cards using the VPX architecture. The only assigned pins are for 3.3V, 5V and 12V power, and both ground and utility planes are defined.
