-
Product
Jerking Tester
JLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;
-
Product
IEC 60884-1 Fig41 High Temperature Indentation Tester For Socket
CX-YH
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 High Temperature Indentation Test Device For Insulatio Material ndentation Device : For pressure tests on plug pin insulating sleeves at temperatures to 200° C with 2.5N loads, according to IEC60884-1 figure 41, BS1363 figure 10. This apparatus has a rectangular blade (see IEC60884-1 figure 41A) with an edge 0.7 mm wide, to be used in the case of round pins, or a blade having a round
-
Product
Miniature Fluxgate Magnetometer
WFG-110
-
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
Product
Instrument ER Shielded Cases
-
The Optima Stantron ER (shielded) and EX (unshielded) family of instrumentation cases are designed to house EIA standard 19” wide sub-racks and chassis. The rugged yet lightweight and stackable structural design is achieved with rigid front and rear aluminum bezels joined by rounded, extruded aluminum corner members. All panels - side, top and bottom are constructed of 18 ga. CRS. Select from a wide range of top, bottom and side panel options. Accessories for doors, shelves, power and co
-
Product
Spring Back Tester
HTJ-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables >
ELCOWIN - Software For 2D-straightness Measurement With Electronic Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
The software ELCOWIN serves for the measurement of straightness, squareness, parallelism of slides and flatness of precision tables by the autocollimation principle. ELCOWIN can be used in connection with electronic autocollimators of the ELCOMAT series from Moeller-Wedel-Optical.
-
Product
Tow Doctor™ Vehicle Side Test Unit
50918
-
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a vehicle has been wired properly and all functions are working. Plug the Tow Doctor™ into the vehicle towing connector, carry the display unit to the cab of vehicle and cycle through the vehicle lighting functions. Includes 7 Blade, 6 Round and 4 Flat adapters and durable carrying case.
-
Product
Rectal Probe For Small Animals
RET-4
-
The RET-4 Rectal Probe for very small animals (mice). Flexible polyurethane sheath with smooth rounded tip.
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
RTM - Measurement Of Positioning Uncertainty Of Indexing Tables
-
Optik Elektronik Gerätetechnik GmbH
RTM is a software for the measurement of positioning uncertainty of indexing tables using an electronic autocollimator and a polygon mirror as angle reference.
-
Product
Right Angle Poppet Valve
PV10
-
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
Product
Solvent Resistance Tester
NRJ-100
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
Product
Waviness, Roundness and Form Analyser
-
SKF Condition Monitoring Center
Waviness testers from SKF allow analysis of the waviness on the components and thus give the production engineer a powerful tool to improve the production process. Because low noise and vibration of bearings is becoming more important, there is a high demand on the measuring accuracy and resolution.
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Gear Teeth Hardness Tester
PHT-1740
-
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1740 is an economically priced hardness tester that is loaded with the same features found on the base 1700 version. The 1740 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
-
Product
Vehicle Survivability
-
Both manned and unmanned military vehicles face numerous kinds of direct fire, varying from incoming Small Arms Fire up to high kinetic armor piercing rounds. Especially when under armor, or unmanned, maintaining situational awareness is key.
-
Product
Automatic Tablet Testing System
UTS 4.3
-
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
Round Handle Style Temperature Sensors
-
A comprehensive selection of round handle hand held temperature sensors to suit a wide range of applications. 14 varieties to choose from.
-
Product
Static Friction Coefficient Tester
JMY-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008; Inspection standard: JB/T4279.16-2008Used to detect static friction coefficient (μs) of enameled round wires with nominal conductor diameter ranging from 0.050mm to 1.600mm;The application of high-end SCM control allows for high sensitivity and excellent repeatability.Four-digit LED would automatically display static friction coefficient (μs) of sample;
-
Product
Atlas DCA Semiconductor Analyser
DCA55
-
Intelligent and flexible semiconductor analyser. Connect any way round! The DCA55 then displays the following on its backlit alphanumeric display:- Component type (such as NPN transistor, P-Ch MOSFET, LED, diode etc)- Pinout information (such as Base, Emitter, Collector etc)- Parameter measurement (hFE, Vbe, Vf, leakage current etc)
-
Product
Edge Radius Measurement
EDGEINSPECT
-
NOVACAMTM EDGEINSPECTTM system is a modular, non-contact 3D metrology system that:Measures, down to the micron, any type of edge: cutting edges, inside or outside edges, edges on round holes, straight edges, etc.
-
Product
PCB Contacts
-
VPC contacts are available in a variety of configurations to support flexible PCB mounting including right angle, vertical, twin female & male, and adapter pins (rounded posts).Many PCB receiver contacts are compatible with standard ITA contactsFor questions regarding compatibility, contact a Field Application Engineer.
-
Product
Computer Controlled Electro-hydraulic Servo Bending Testing Machine
SBT Series
-
Jinan Testing Equipment IE Corporation
SBT series computerized bending testing machines are mainly used for bending and pressing tests for metallic sheet & round bars as per standards of GB/T232-2010 & ISO 7438-2005 Metallic Materials-Bend Test. An axial oil cylinder for bending test is installed on the top cross-head. Two pressing oil cylinders are installed at both sides of the frame, which adopts the synchronous control, to realize the pushing and pressing force on the bending support to adjust the distance between pivots. The pressure meter indicates the pressure in bending or pressing. Various load display can be selected, such as display through the pressure meter, digital display, and computer screen display etc. The computer control type SBT bending testing machine can do the bending test automatically or manually. TThe applies bending force can be adjusted or controlling the oil feed valve.
-
Product
6-way Round Pin Vehicle side Circuit Tester
7897
-
Innovative Products of America
The 6-way Round Pin Trailer Circuit Tester tests trailer circuits on older light to medium duty trucks and RVs. Plug the 6 pole trailer tester into the back of the vehicle and apply the Brake Lights, Turn Signals, Running Lights etc.
-
Product
Continuous Internet Speed Test Tool
-
*Internet speed stress test with long duration: long-term download and upload bandwidth (speed) test tool*Cross-platform: HTML (online), Windows, Linux, Android versions, free for non-commercial use (please contact us to get a commercial license)*Measures download and upload bandwidth, packet loss and round trip time (RTT, ping)*Measures and tracks bandwidth of your internet connection during a long (unlimited) period of time*Measures stability of internet connection (uptime in percents, bandwidth measurements)*Tracks connection outages and drops of bandwidth*Runs on your own Windows PC as a server, to check stability of your LAN/wifi router(s)
-
Product
Calipers - Digital/Electronic
-
Use a digital encoder that displays measurements on a screen instead of the rack and pinion system that analog calipers display on a round dial.
-
Product
Instrument EX UnShield Cases
-
The Optima Stantron EX (unshielded) and ER (shielded) family of instrumentation cases are designed to house EIA standard 19” wide sub-racks and chassis. The rugged yet lightweight and stackable structural design is achieved with rigid front and rear aluminum bezels joined by rounded, extruded aluminum corner members. All panels - side, top and bottom are constructed of 18 ga.
-
Product
7 Round Pin Tractor-Trailer Circuit Tester
IPA7865
-
Troubleshoot male and female 7 round pin tractor trailer electrical circuits on both the truck and trailer side. Allows bypassing of troubled circuitry while on the road.
-
Product
Flocculation Jar Tester
LD-LFC-A12
-
Flocculation Jar TesterLD-LFC-A12is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features desktop, 6 round shaped or square shaped beakers, each with 1.0 L and 1.5 L capacity respectively. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
Product
LXI Chassis X Plugin - 8x16 Matrix
65-110-202
Matrix Switch Module
The 65-110-202 is an 8x16 matrix plugin for the 65-110A chassis. At least one is required to be fitted to these chassis assemblies that are configured for Y=16 applications. The number of plugins is determined by dividing the X axis size required by 8 and rounding the number up to the next integer.
