LINEEYE Co., Ltd.
LINEEYE CO., LTD. manufactures interface converters and compact high-performance Portable data communications Analyzers that are capable of on-line monitoring and simulation.
- 81-75-693-0161
- 81-75-693-0163
- 4F Marufuku Bldg. Karahashi
Nishihiragaki-cho
Minami-ku, Kyoto 601-8468
Japan
-
Product
Modbus TCP Gateway
SI-485MB
-
SI-485MB is a Modbus gateway to convert bi-directionally Modbus RTU/ASCII of serial interface to Modebus TCP of Ethernet. The firmware for gateway process supports Modbus TCP master mode and Modbu TCP slave mode and supports all the current ModbusRTU/ASCII register and command conversion. The robust metal body, broad range of temperature, wide input voltage range, and the support for installation by options such as 35mm DIN rail and wall bracket allow you to use it for factory automation without worry.
-
Product
LAN⇔RS-232C Conversion
SI-60F
-
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
Product
CAN/LIN Communications Expansion Kit
OP-SB7FX
-
OP-SB7FX is the expansion kit which makes it possible to monitor, and simulate CAN and LIN communications. It enables monitoring of CAN and LIN data in any combination up to 2 channels at a time. Suitable for evaluation of mixed in-vehicle networks of CAN and LIN.
-
Product
Current Loop Expansion Kit
OP-SB85C
-
This expansion kit supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
CAN/LIN Communications Expansion Kit
OP-SB87
-
OP-SB87 is an expansion board for CAN/LIN communications, inserting into a slot of communication analyzer LE-8200A/LE-8200. It has 2 CAN connectors and 2 LIN connectors, and measures 2 channels of CAN or LIN, or 1 CAN/1 LIN. It is useful to measure network where there are CAN and LIN communications at the same time.
-
Product
TTL/I2C/SPI Expansion Kit
OP-SB85L
-
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
Product
Communication Data Logger
LE-270GR
-
LE-270GR is a Communication Data Logger, which has acceleration sensor and a connector for GPS antenna. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data or GPS data on the PC at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on PC. It has galvanic-isolated two CAN transceivers and two LIN transceivers. Thus you can measure 2 channels of CAN/LIN communication lines and can simultaneously register GPS positioning data, acceleration data, and voltage data of 4 external signals.
-
Product
Multi Protocol Analyzer
LE-3500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
The PC Link Software For CAN/LIN Data
LE-PC87
-
This PC link software “LE-PC87” captures CAN/LIN data into PC measured by the CAN/ LIN optional expansion kit for LE-8200A/LE-8200.
-
Product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
-
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
Product
LAN⇔RS-232C(2ports) Converter
SI-60X
-
SI-60X is an interface converter that converts 2 serial ports of RS-232C devices to Ethernet LAN at 10Base-T/100Base-TX. The built-in Lantronix WiPort® NR on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. The small housing ensures ease of use for FA applications, public facility and medical institution as a communication device server.
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65A
-
SI-65A is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
Line Monitor
LE-120SA
-
LE-120SA is a handheld line monitor specialized for ASYNC communication which is widely used in the industry. You can control the line monitor by soft screen touch as you do for smart phones. The light weight (300g including batteries) helps you for the field maintenance besides the system developments.
-
Product
FlexRay Communications Expansion Kit
OP-SB88
-
The FlexRay communication is anticipated as a next-generation high-speed in-vehicle network.The OP-SB88 is an expansion kit that allows monitoring of FlexRay communications on up to two channels in real time. The kit incorporates a monitor function that does not require complicated parameter settings, and a simulation function with which the OP-SB88 works as a FlexRay communications node to transmit and receive data, thus powerfully supporting the initial development. The filter function and high-capacity memory greatly shorten the analysis time of trouble.
