VECTOR Electronics and Technology, Inc.
We offer the shortest lead-times in the electronics industry with extensive factory-stock selection of 19" rack mount systems packaging and prototyping products. We have a growing number of aerospace, military and commercial OEM accounts in addition to national distribution channels for our Vectorbord® products.
- ( 800 ) 423 5659
( 818 ) 985 8208 - ( 818 ) 985 7708
- inquire@vectorelect.com
- 11115 Vanowen St
North Hollywood, CA 91605
United States of America
-
Product
Plugbord
4066-4
-
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. Overall ground plane on wiring side. Interleaved zig-zag bus pattern on component side.0.085” diameter etched clearance area around each hole on ground plane sideBus and plane surface solder coated for user convenienceRow and column legends provided
-
Product
EMC-Gasketed Front Panels
-
VECTOR Electronics and Technology, Inc.
EMC Front panels are designed to mount 3U, 6U and 9U Eurocard size PCBs to front panels. Applications with high connector pin counts, where high insertion/extraction force needed. They are fitted with EMC gasket that interfaces with adjacent panels to create RFI shield and does not snag when adjacent cards are extracted.
-
Product
Circbord
8003
-
VECTOR Electronics and Technology, Inc.
Pad per hole & peripheral ground plane.0.085” Square pads etched around each hole on wiring side.Accommodates any type DIP IC device or discrete component.Single sided board with pads and peripheral GND plane on one side only.Single-sided with no etch and plating on reverse side.
-
Product
Vectorbords
-
VECTOR Electronics and Technology, Inc.
General purpose pre-punched insulating punchboard is available in variety of grid patterns shown below for assembling circuit components. Vectorbord® is available in FR4 epoxy glass, FR2 phenolic, CEM-1 epoxy glass composite and FR4 HiTg 170°C materials. Vectorbord® listed below is unplated copper clad on one side, both sides or unclad with no copper layer on either side.
-
Product
IBM AT/ISA, Vectorbord Plugbord
4617-1
-
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers.Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated.I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
Extrusion Rail
1440-0013-84
-
VECTOR Electronics and Technology, Inc.
To accommodate guide rails and attach backplanes.HP pitch pattern of holes for precise installation of card guides.M4 threaded at ends.
-
Product
Backplane
P47
-
VECTOR Electronics and Technology, Inc.
Power supply backplane provide a modular approach for the addition of plug-in, hot-swap power supplies. As a result there is no need to modify expensive backplanes to incorporate redundant power supplies or N+1 configurations. Multiple power supply backplanes may be bridged together for additional power supply requirements.
-
Product
S-100 Bus, Vectorbord Plugbord
8801-1
-
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side) on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
Product
Eurocard Plugbord
4615
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiplecomponent leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience.Green Solder Mask both sides. Row and column legends provided.
-
Product
Extrusion Rail
5250998-84
-
VECTOR Electronics and Technology, Inc.
Fits onto rear face of rear extrusion rails, in between backplaneand extrusion rail to isolate backplane from extrusion.HP pitch pattern of holes for precise installation of backplane.
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-3
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
Extrusion Rail
1440-0132-84
-
VECTOR Electronics and Technology, Inc.
To accommodate guide rails and attach backplanes.HP pitch pattern of holes for precise installation of card guides.M4 threaded at ends.
-
Product
Plugbord
3662-5
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
Product
6U Vertical Card
439
-
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
Product
PCI Expansion Card
4624-4
-
VECTOR Electronics and Technology, Inc.
120 contacts (60 each side) on 0.050" centers. Pad-Per-Hole & Peripheral Buses. 32-bit ISA format. Universal tab fits both 3.3V and 5V tab notch patterns. Mounting bracket included. Peripheral buses for voltage and ground distribution. I/O mounting area for D-sub and ribbon cable connectors.
