Aero Nav Laboratories, Inc.
Aero Nav Laboratories is a full service environmental simulation lab that has served the military and industrial communities.
- 631-392-4888
- 631-392-4883
- AeroNavLabs@aeronavlabs.com
- 18 Connor Ln
Deer Park, NY 11729
United States of America
-
Product
Fire & Flammability Test
-
Fire & Flammability testing: ASTM E119 [UL 263]; ASTM E152 [UL 10C]; ASTM E814 [UL 1479]; API 607, 6A; ASTM E108 [UL 790]; UL 1709; UL 1715; UL 2043; NFPA 286; UBC 26-2; UBC 26-3; ASTM E84 [NFPA 255, UL 723]; ASTM E162; ASTM E662 [NFPA 258]; ASTM D635; ASTM D1929; ASTM D2863; ASTM E1354; ASTM E1317; Room Burn Facility; CAL 133, 117, 129; UL 94 V/HB; IMO A.652 (16); IMO A.653 (16); ULVW I; ASTM D2859; AITM 2.0007; NFPA 701; FMVSS 302; FAA 25.853; IEEE 383
-
Product
Electric Power System Characteristics Test
-
This test is also known as the power supply line voltage and frequency variations test. A few of the measured characteristics are: voltage and frequency modulation, voltage spike, and voltage transient recovery.
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
-
Product
Induced Signals Test
-
The test relates to interfering signals that may be generated by interconnected equipment. Induced signal testing is used to determine if equipment will withstand various signals, such as might be introduced by failures in other equipment to which the test unit is connected.
-
Product
Solar Radiation (Sunshine) Test
-
This test determines the effects of direct solar radiation on components and material. The heating effects of solar radiation differ from those of high air temperature in that the amount of heat absorbed depends on the roughness and color of the surface on which the radiation is incident and the angle of incidence to the sun. Variations in the intensity of solar radiation over the surface of the component, may cause components to expand or contract at different rates, which can lead to severe stresses and loss of structural integrity. In addition, degradation due to photo-chemical changes can occur such as fading of color, deterioration of natural and synthetic elastomers and polymers. The test items that are subjected to solar radiation testing are those that are exposed to solar radiation during its life cycle, in the open, in warm climates.
-
Product
Physical Testing Test
-
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
Product
Testing Services Test
-
Aero Nav Laboratories is uniquely positioned to provide testing services that promote safe and reliable products, which are in compliance with the government and industry standards.
-
Product
Package Handling Test
-
This test subjects packaged items to the stresses encountered during handling, transportation and storage. The tests consist of drop tests, storage tests such as stacking and compression, temperature tests and transportation vibration tests.
-
Product
Electrical Measurements Test
-
The tests are performed to measure and collect data from electrical and electronic parts using various measurement methods including, but not limited, to the following: capacitance, resistance, winding resistance, insulation resistance, magnetic permeability, power input, and quality factor Q.
-
Product
Accelerated Weathering Test
-
Accelerated weathering consists of relatively long term exposure of items to specified environments.This test is designed to observe for material degradation.
-
Product
Magnetic Effects Test
-
This test determines if an object can operate normally in strong externally generated magnetic environments. The magnetic effect test helps to assist in determining the proper location of the equipment in the installation.
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Enclosures
-
An enclosure is a mechanical item which either partly or wholly surrounds a component or assembly. Enclosure tests determine the suitability of equipment enclosures and sealing design techniques to provide various functions, including the following: Physical and environmental protection to the enclosed items. Protection from items within the enclosure to personnel or objects outside the enclosure.Means for ventilating items within the enclosure. Means for cooling items within the enclosure. Sealing equipment to protect against leakage, both internal and external. Enclosures are designed to provide various degree of protection.
