ALPHI Technology Corporation
Alphi Technology designs and manufactures board level products. We specialize in Industry Pack Modules, Industry Pack Carriers MIL-STD-1553, Serial Communications, Data Acquisition & Control and Digital Servo Controllers, Analog and Digital converters. We offer one of the largest selection of Industry Pack Modules and IP replacement. We serve the Military / Aerospace industries, Test Industry, Automotive, Semiconductor and OEM’s that requires measurement and control solutions.
- (480) 838-2428
- (480) 838-4477
- info@alphitech.com
- sales@alphitech.com
- 1898 E. Southern Ave.
Tempe, AZ 85282
United States of America
-
Product
One Channel Dual Redundant 1553 Controller
PCIe-Mini-1553-1TA
Controller
The ALPHI PCIe-Mini-1553-1TA uses DDC TotalAce communication device as its 1553 bus controller, or remote terminal with concurrent Bus monitor terminal. Dual controller has a Dual redundant channel with built in transceivers andtransformer. The controller has the capability to emulate up to 31 RT addresses simultaneously. The PCIe-Mini-1553-2in RT mode can filter on RT address, T/R, Subaddress.
-
Product
XMC Module
XMC-FPD-xxx
-
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level
-
Product
Single or Dual Summit Controller
CPCI-1553
Controller
• Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
3U CPCI Dual IP Carrier
CPCI-SIP
-
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry. PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution. The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
Product
6U CompactPCI Multifunction I/O Board
CPCI-MFIO-6U
Multifunction I/O
The CPCI-MFIO-6U is a 6U CompactPCI multifunction I/O board. The CPCI-MFIO-6U offers 32 channels of 16 bit A/D, four 16 bit D/A, 16 digital I/O, counter / timers, and one PMC expansion slot for additional I/O. There is a local 60 Mhz TMS320C31DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-MFIO-6U is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
VME Module
VME-5SIP
-
The new VME-5SIP Module provides a 6U high performance flexible I/O scheme, that supports industry standard Industry Packs. Choose from over a 100 different Industry Packs from Alphi Tech and others.
-
Product
High Performance Data Acquisition
PMC-AD8
-
The PMC-AD8 module provides a high performance dataacquisition subsystem. There are (8) eight 200 KSPSADC’s for maximum performance. The Local DSP can beused to simply move data samples to the PMCbus or canprovide processing functions such as limit checking, FFT’s,digital filtering, etc. Software can be downloaded to theDSP via the PMC interface. Instrumentation amplifiersprovide over-voltage protection and gain on a per channelbasis. The PMC-AD8 can also accept external scan andtrigger signals from a front panel connector.
-
Product
PCIexpress Module
PCIe-1553-x
-
1 or 2 UTMC SUMMIT• UT69151DX-GPC• BC / RT / BM• On-chip Transceivers• On-board Transformers• Long stub / Short stub
-
Product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
Controller
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
Product
Bus Controller
CPCI-1553-1
Controller
Single or dual UTMC 1553 Summit Controller, Bus controller, Remote terminal, Bus monitor modes.
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
PCIe Module
PCIe-1553-uAce-1,2
-
1or 2 controllers of dual redundant (A/B channel) 1553 communications• Programmable bus controller, remote terminal, or monitor terminal modes• MIL-STD-1553 A and B compliant, Notice 2 RT• STANAG 3838 bus compliant for NATO standard support• Long or short stub support • Low power consumption• PCIMG compliant• Single +5 VDC supply
-
Product
PCI/DSP Module
PCI-4pack-2
-
The PCI-4pack module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4pack is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc.Custom application software can be downloaded to the DSP via the PCI bus. Windows 95 and WinNT drivers are standard.
-
Product
PCIe Mini Module
PCIe-Mini -IO Controller
Controller
High Speed CAN interface according to ISO 11898-2 • Time-stamped CAN messages• Supports 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers• Bit rates” 10 to 1000 kbps• Reliable error handling• Low Power consumption• NEMA Compliance• Isolated CAN Channels
-
Product
CompactPCI
CPCI-ADDA
-
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
