Switch Test
Make, break, or change the connection of a circuit.
-
Product
Single 16x8 1-Pole High-Density PXI Matrix Module
40-520-203
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
LXI 2.4GHz 50ohm 32x4 Matrix
60-772-001
-
The 60-772 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 4 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
Product
PXI BRIC8 FIBO Matrix Dual 124x4 2pin brkout
40-592A-114
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Design for Testability (DFT Test)
-
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
PXI 4x3 20GHz Matrix
40-787-528-4X3
-
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI 4-Slot BRIC 48x8 Matrix, 2A 2-Pole (2 sub cards)
40-565A-002-48X8
-
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
2m BNC Test Cable
16048D
-
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
PXI 4 Slot BRIC 75x4 2A 1-Pole Matrix
40-568-001
-
The very high-density 2Amp PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Standard 0.88 (24.90) - 4.50 (128.00) Switch Probe
SSP-5C
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Spring Force Remark: Force at switch point: 2.36 (66)Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 150Full Travel (mm): 3.81Recommended Travel (mil): 100Recommended Travel (mm): 2.54Mechanical Life (no of cyles): 100,000Overall Length (mil): 1,210Overall Length (mm): 30.73Switch Point (mil): 25Switch Point (mm): 0.64
-
Product
PXI 8-slot BRIC Matrix, 2A, 2-Pole, 342x4, 6 Sub-cards
40-574-106
-
The 40-574-106 is a 342x4 2-pole matrix and is part of a range of BRIC matrices providing high density configurations capable of switching signals up to 2 A. The modules are available in 2, 4 or 8-slot PXI sizes and are constructed using high quality electro-mechanical relays.
-
Product
PXI 12-Slot BRIC Matrix, 168x12 1-Pole (4 sub-cards)
40-558-121-168X12
-
The 40-558-121-168x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Matrix Switch Module
-
PXI Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 224x8, 1-Pole (7 sub-cards)
40-563B-121-224X8
-
The 40-563B-121-224x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
PXI 4 x Changeover Switch 2.5GHz, 50 SMA
40-710-524
-
Model 40-710 RF switching card has a bank of 4 individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analysers. Available with a choice of connectors: SMA, SMB and Siemens 1.0/2.3 versions. BNC versions are also available with reduced bandwidth and 2 PXI slot occupancy.
-
Product
PXI 8-slot BRIC Matrix, 336x12, 1 pole (8 Sub-cards)
40-558-801-336x12
-
The 40-558-801-336x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 138x16 1-Pole (6 sub-cards)
40-560A-021-138X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 224x16 1-Pole (7 sub-cards)
40-558-121-224X16
-
The 40-558-121-224x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
2X8 USB Solid State Switch Matrix, 300 KHz To 9 GHz
P9165B
-
P9165B 2X8 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
PXI 4x4 10GHz Matrix with Loop-Thru & Term
40-787-518-4X4-L-T
-
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
PXI 8-Slot BRIC Matrix, 121x16 2-Pole (11 sub-cards)
40-562B-122-121X16
-
The 40-562B-122-121X16 is a high density BRIC8 matrix module with a size of 121x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 88x4 1-Pole (2 sub-cards)
40-562A-121-88X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
VLSI Test System
3380
-
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
High Throughput Test Platform for Multi-Site & Index Parallel Applications
ETS-88
-
The ETS-88 is an optimal test platform for testing a wide variety of devices including: simple analog, high precision, high voltage, high current / power, automotive, video, audio, complex mixed-signal, as well as emerging power processes like SiC and GaN.
-
Product
PXI 8 Slot BRIC 198x8 2-pole (9 sub-cards)
40-562A-122-198X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
VLSI Test Systems
-
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 75Ω, SMB
42-837A-001
-
The 40-837A-001 (PXI) and 42-837A-001 (PXIe) are 75Ω 2x2 RF matrices with 1 bank in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
PXI 4 Slot BRIC 165x4 2A 2-Pole Matrix
40-566A-003
-
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI/PXIe RF Switch, Quad SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-002
-
The 40-880B-002 (PXI) and 42-880B-002 (PXIe) are quad SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in two slots or hex and octal switches in three slots.
-
Product
LXI Microwave Matrix, 10GHz, Single 3x3 With Loop-Thru
60-750-133-A
-
The 60-750-133-A is a single 3x3 10GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection.
-
Product
PXI 8-Slot BRIC Matrix, 66x8 2-Pole (3 sub-cards)
40-562B-122-66X8
-
The 40-562B-122-66X8 is a high density BRIC8 matrix module with a size of 66x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
