-
Product
Cyber Security Assessment
-
In the Internet of Things, everyone and everything is at risk of becoming a victim of cyber attacks.Protection against cyberspace threats is particularly relevant and important for connected devices.Messages about defective devices and successful attacks, which can also be carried out with very simple means, are increasing.Third party verification can be helpful in building trust by confirming and demonstrating an adequate level of protection.
-
Product
Testing and Validation
-
DA-Group offers accredited testing services for a wide range of electronic and mobile solutions and products. Testing and measuring are necessary during many phases of product development, manufacturing, verification and delivery. Timely and appropriate testing saves time, because this information is fed back to the development process.
-
Product
Test a Service
-
Enabling the automation of regression testing, verification, and validation within a functional safety environment
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
TRA-300 LED Thermal Resistance Structure Analyzer
-
Hangzhou Everfine Photo-E-Info Co., LTD
The TRA-300 accurately measures the thermal resistance, junction temperature, optical power, voltage, current and other parameters of LED packaging products.The heating and cooling curves of LED can also be obtained, and the integral and differential thermal structure functions can be obtained by establishing the finite element model.Through the structural function analysis of the TRA-300 special software, the fine thermal resistance structure of the LED (from the chip to the thermal resistance value of each package structure) can be obtained, so as to objectively evaluate the heat dissipation quality and thermal management level of the LED package products, and provide the best verification for the heat dissipation design of the LED.
-
Product
High Performance Embedded Development Kit
TySOM EDK
-
The TySOM™ Embedded Development Kit is for the embedded designers who need a high-performance RTL simulator/debugger for their embedded applications such as IoT, Automotive, Factory automation, UAV and Robotics. The kit includes Riviera-PRO™ Advanced Verification Platform and a TySOM development/prototyping board. TySOM boards come with either a Zynq 7000 chip (FPGA + Dual ARM® Cortex™-A9) or with a Zynq® UltraScale+™ MPSoC device. These boards include memories, and various communication and multimedia interfaces in addition to FMC connectors for peripheral expansion. Reference designs for application such as IoT, ADAS, 4K UltraHD imaging and Robotics and a complete reference design, which contains the SW (Linux) and all the hardware blocks required to support the peripherals on the board, are provided.
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Business Application
-
Business Application testing encompasses verification and validation services to support Quality Assurance and Control of business applications. Application testing ensures that all aspects of the application like its functionality, integration, performance, security, and usability are working as expected.
-
Product
Calibration And Verification Instruments
-
The system of automatic calibration and verification consists of a computer of the operator's workplace and a control controller with a calibrator connected to it and a verified device. The device under test can have 4 to 16 working channels with a complicated circuit for connecting different types of signals: voltage, current, thermocouples, thermoresistance. The system allows a change in the set of operating ranges during calibration and calibration. The software development system used the LabVIEW development environment with the Real-Time module.
-
Product
ReferenceWafer
RW10
-
Materials Development Corporation
MDC presents the RW10 Reference Wafer. A range of capacitors, resistors and semiconductor devices can bemeasured to verify the repeatability and accuracy of measurement systems. The MDC Model RW10 Reference Wafer is not actually a "wafer". It has the shape of a wafer and it includes capacitors, resistors, MOS devices, and a junction device in a wafer configuration to allow rapid verification of proper operation for capacitance-voltage and current-voltage instrumentation.
-
Product
”Two Pressure" Humidity Generator
2500 Mobile
-
The Model 2500 Benchtop Humidity Generator is a self contained system capable of producing atmospheres of known humidities using the fundamental, NIST proven, "two-pressure" principle. This system is capable of continuously supplying accurately known humidity values for instrument calibration, evaluation, and verification, as well as for environmental testing.
-
Product
Semiconductor Authenticity Verification & Anti-Counterfeiting
JTAG Interrogator
-
Top manufacturers have used JTAG tests for years to ensure electronic systems are free from defects and assembled correctly. With growing uncertainty in supply chains and the proliferation of counterfeit components, that same technology can be used to verify the authenticity of system components.The Corelis JTAG Interrogator is an affordable solution for semiconductor verification. The software and hardware system provides the means to quickly identify components on an assembled electronic product by reading available information from the JTAG chain. Components can also be scanned to discover undocumented opcodes that may indicate hidden JTAG capabilities such as backdoors and harmful or malicious functions.Fast and nonintrusive JTAG component identification has never been so easy.
