RF Attenuators
Used to reduce input RF & Microwave power by a fixed ratio – expressed in dB. (www.e-meca.com)
-
Product
RF Shielded Test Enclosure, Large, Yet Benchtop Enclosure
JRE 2525
-
Originally designed for testing rack mounted RF Sensing equipment, the roomy JRE 2525 is ideal for large wireless devices such as; Rack Mount Mesh Network AP's, Cellular/LTE/4G Base Stations, Wireless Laptops, Test Fixtures for testing Large RF Modules, and other large RF devices.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, SMB
42-877A-001
Matrix Switch Module
The 40-877A-001 (PXI) and 42-877A-001 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm 1.0/2.3
45-720A-741
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI Dual 4 to 1 RF MUX SMB 75 Ohm
40-832-002
Relay
The 40-832-002 is a 75 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-832 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Manual Attenuator (Coaxial)
-
Manual control coaxial attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
Product
RF spectrum analysers
-
Electronics laboratories instruments, technical schools and spectrum analysis in field for Wi-Fi, GSM, PLC and high frequency.
-
Product
PXI Programmable Step Attenuator Module, DC to 50 GHz
M9168E
Attenuator
The M9168E is a programmable step attenuator module based on PXI hybrid platform. The M9168E operates from DC to 50 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
Generic RF ATE Test
-
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
Product
Single 32 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-767A-001
Multiplexer Module
The terminated single 32 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
RF Mixers
-
An RF mixer is a three-port passive or active device that can modulate or demodulate a signal.
-
Product
Dual Attenuator
V859
-
The Model V859 is a passive dual section attenuator housed in a 1-unit VME module; the module does not require any power supply since it is made up of resistive cells
-
Product
Dual 16 to 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-765A-002
Multiplexer Module
The 40-765A-002 terminated dual 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
RF Safety Monitoring
MVG EME Guard XS Radar
-
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
Product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI Hex SPDT RF Switch 3GHz 50 SMB
40-870-006
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, MCX
40-877A-101
Matrix Switch Module
The 40-877A-101 (PXI) and 42-877A-101 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
RF Power Monitors
-
Bird's RF Power Monitor family includes a range of products that not only measure power and VSWR but also provide hard contact alarms to protect your system in the event of a system failure – the IP-enabled, BPME is even capable of emailing a failure notification.
-
Product
RF Power Controller (ALC)
310-010030-004
-
The serial controlled ALC module is used to set and monitor the output level of your fixed gain RF amplifier. The module is available for many bands between 800 MHz and 3 GHz, and is configured and calibrated to meet your requirements.
-
Product
Fixed Attenuator (Coaxial)
-
RF Lambda’s fixed coaxial attenuators are used to adjust the signal level in any RF system. They are most commonly used to reduce high power signals in order to inject into test equipment or other parts of the RF system requiring lower signal levels. They are highly reliable and come in a variety of frequencies, powers, and connectors.
-
Product
Variable Optical Attenuators
5420
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
RF Switching PXI Card
GX6062
Switch Module
The GX6062 is a high-density 6U PXI RF switching card that provides 200MHz bandwidth and multiple switching configurations. The GX6062 has 12 groups of 1 x 4 differential, non-terminated RF multiplexers. The 12 groups can be used to create multiple configurations including: 6 x 1:9, 3 x 1:19, 2 x 1:29, 1 x 1:59, and more. The GX6062 switching card plugs directly into any 6U PXI chassis.
-
Product
MXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5182B
Vector Signal Generator
Take your designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading ACPR & output powerTest wideband devices with factory-equalized 160 MHz RF bandwidthReduce the time spent on signal creation with Signal Studio software, including LTE, WLAN & GNSSLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
Product
RF / MW switch
-
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
Product
PXI Single 16 to 1 RF Multiplexer, 8GHz 50Ω SMA, Terminated
40-883A-002
Multiplexer Module
The 40-883A-002 is a single 16 to 1 50Ω RF multiplexer with 8GHz bandwidth and automatic termination of unused signal channels. It is available in 8 to 1 and 16 to 1 configurations in two and three PXI slots respectively.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, MCX
42-830A-103
Switch Module
The 40-830A-103 (PXI) and 42-830A-103 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
LXI RF & Microwave Matrices
-
Each of our RF & Microwave matrices is designed to have a controlled transmission line impedance and architecture developed to maximize the bandwidth of the product. The RF matrices are designed with crosspoint switch systems interlinked with isolation relays and loop-thru connections to minimize stub loading of the matrix. The mechanical and electrical freedom of LXI allows us to design RF and Microwave matrices to suit most applications.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
Elite™ 13.56 MHz RF Plasma Generators
-
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
Product
Direct Reading Attenuator with Remote Control
DA2XE
-
DA2XE Millimeter-Wave Direct Reading Attenuator is a measurement instrument for signal level setting or loss measurements in waveguide networks. It also can be used for calibration of other attenuation measurement instruments. Direct Reading Attenuators have rotary-vane design. The value of attenuation is determined by rotation angle of resistive film with respect to the waveguide channel. Attenuation value does not depend on frequency. The attenuator has electronic control. The attenuator can be used in local or remote (via USB 1.1 or higher) operation modes.The Attenuators are provided in waveguide bands between 18 GHz and 225 GHz.
