Rapid IO
"the unified fabric for Performance Critical Computing"; rapidio.org
-
product
LVDS Digital I/O with Kintex UltraScale FPGA - 6U VPX
Model 58810
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
product
Serial I/O Expansion
It is well suited for embedded applications requiring a large number of serial I/O ports. Each channel supports RS-232, RS-485, and RS-422 electrical levels to interface to a wide variety of serial communications devices such as modems, data collection equipment, and distributed I/O terminals. The PCM-COM8 will operate over the full industrial temperature range of -40 to +85 Celsius.
-
product
SparkFun 16 Output I/O Expander Breakout
SX1509
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
product
PCIe-7852, Virtex-5 LX50 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781103-01
Virtex-5 LX50 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7852 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7852 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
-
product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
PCI Express Analog and Digital I/O
826
Six advanced 32-bit counters Directly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement 16 analog inputs, 16-bit, 300 ks/s 8 analog outputs, 16-bit, 900 ks/s 48 digital I/Os with edge capture Watchdog timer, 3 stages
-
-
product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
DB37F-DB37M LP, Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
154302-01
Low Profile I/O Cable, 37-pin Female DSUB to Male DSUB (1m)
-
product
Isolated/Relay Digital I/O Terminal
Isolated digital I/O terminals boards and I/O wiring boards offer isolated input channels. The I/O terminals also feature high-voltage protection.
-
product
FPGA Digital IO XMC
XF07-523
Curtiss-Wright Defense Solutions
The XF07-523 is a rugged Kintex-7 FPGA based XMC with digital IO. The combination of direct high-speed I/O ports and FPGA processing makes the XF07-523 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces. The XMC form-factor is ideal to SWaP constrained platforms such as UAVs and fighter aircraft.
-
product
Static Digital I/O Instrumentation
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
Loopworks Measure iOS App
Loopworks is a unique suite of online and App-based tools and resources designed by Ampetronic to enable its customers to understand, specify and design Hearing Loop systems.
-
product
PoKeys I/O devices
This board allows expanding the number of outputs of the Pokeys by using the PoExtBus. This board incorporates 16 high current/voltage open collector outputs which suits applications such as lamps, relays.
-
product
PLD For Bridging, Infinitely Reconfigurable I/O Expansion.
MachXO
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
product
FPGA Serial Controller Card with Front & Rear I/O
8046
The 8046 is a PMC FPGA-based RS422 serial card with front and rear I/O.
-
product
Isolated Digital I/O Card
mPCIe-IDIO-8
The mPCIe-IDIO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
product
Mobile Apps for iOS and Android
LoggerLink
LoggerLink Mobile Apps are simple yet powerful tools that allow an iOS or Android device to communicate with our CR200X, CR800, CR850, CR1000, CR3000, or CR6 dataloggers via an IP device (NL115, NL116, NL120, NL121, NL201, NL240, RavenXTV, RavenXTG, LS300G). LoggerLink for Android also supports Bluetooth communication for these same dataloggers using an RS-232-Bluetooth adapter. The apps support field maintenance tasks such as viewing and collecting data, setting the clock, and downloading programs.
-
product
AcroPack® I/O Modules
Acromag provides software support packages for embedded applications running on Linux®, Windows®, or VxWorks® operating systems. The libraries provide generic routines to handle reads, writes, interrupts, and other functions. Demonstration programs enable the developer to quickly exercise the I/O modules before attaching the routines to the application program. This diagnostic tool can save hours of troubleshooting and debugging.
-
product
PXIe-6378, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781476-01
PXIe, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6378 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6378 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PXIe-7820, Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module
783484-01
Kintex 7 160T FPGA, 128 DIO, PXI Digital Reconfigurable I/O Module—The PXIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7820 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
Safety Certified I/O Modules
HY-TTC 48XS
HY-TTC 48XS is an intelligent safety I/O module for extending the number of I/Os in mobile applications. The I/O module acts as a slave and is used in combination with, and controlled by a master electronic control unit and communicates via the standardized CANopen protocol, parameterized according to CiA DS 401. It is also compliant to the European Standard EN 50325-5 for CANopenSafety and is developed in accordance with the international standard EN ISO 13849 on functional safety, performance level (PL) d.
-
product
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
192568-01
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
-
product
Digital I/O via Ethernet
2610
Connects to Ethernet via 2601 communication moduleAll channels may be independently programmed as input or outputEight channels have pulse width modulation outputsRJ-11 I/O connectors eliminate need for external terminal blocksSupport for interlocks and multiple power supplies per channelInput channels are debouncedWatchdog Timer
-
product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A200
Sundance Multiprocessor Technology Ltd.
The EMC2-7A200 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
