LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Handheld Water Quality Meters
LAQUA PH210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
Product
Function Generator
FG-102
-
*0.3Hz~10MHz *Hz.KHz.MHz..3Range, Easy Operation.*LED: 0.56", 6 Digits. *2 Attenuator: (-20dB x 2) *USB (RS-232) Built-In.*PC Control: Frequency, Waveform, -20dB Attenuator. Duty Cycle*Accuracy: 10PPM, Longtiome: ±1ppm/year*Waveform: Sine, Square, Triangle to 10MHz*Duty Cycle Range 0.3Hz~3MHz
-
Product
METES - Meter Test Systems
-
Dramatic advances in the field of measurement technology and the use of state-of-the-art micro-electronics have led to the development of a new generation of electricity meters which are far more accurate than their predecessors of just a few years ago. As well as measuring the exact amount of energy used, a high level of integration enables electronic meters to perform a number of additional functions. As a result, these meters are also more sensitive to network irregularities. This means that regular testing is the only way to ensure that a meter functions correctly, both during final factory tests and during the entire life span of a meter.
-
Product
LED Illuminator
-
Luzchem's LED-Illuminator, is a compact system for irradiating samples from 3-200 ml in size. Features a unique 7-LED design with lenses that focuses all LEDs on one spot! LEDi-KIT3 includes Luzchem's standard RGB head, comprised of two red, two green, two blue and one white LED. Or, choose from our broad range of high-powered single-coloured LEDi-Heads.
-
Product
Optical Light Sources
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.
-
Product
Triple IC Optic Node
OX 733
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Tecnology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -13 dBm Sensitivity- RF O/P at 0 dBm : 113 dBµV
-
Product
Breakdown Voltage Tester
ZDS-50B
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.11-2008Used to test the breakdown voltage performance under room temperature of enameled round and flat wires with nominal conductor diameter of 0.018mm and above;Three voltage rise speeds are available: 20V/s, 100V/s and 500V/s, with error being ±5%;Three test methods can be adopted: round bar method, twist pair method and ball method;Clamp a group of test samples (5 for each) once, available to complete breakdown or withstand voltage test for any of sample one by one or individually; breakdown voltage and withstand voltage time would be automatically saved for future enquiry; all operations would be automatically completed;Capable of conducting high temperature breakdown voltage test in combination with RDS-50 thermal-state voltage tester;LED would automatically display test results and automatically return;During sample breakdown, breakdown voltage indication value would be automatically locked, free from flashing, and the test result is distinct and relatively clear;Equipped with test fixture for round rod method and twist pair method as well as the test weight for round rod method;Equipped with ball method test device (steel balls are prepared by user);Test door is provided with safety interlocking device, compliant with relevant regulations on high voltage testing equipment.
-
Product
Light
-
Welcome to Thorlabs; below you will find links to light emitters, sources, and controllers, a subset of our entire line of photonics products. Our light sources are conveniently separated into coherent and incoherent sources. The coherent source category includes laser diodes, laser diode modules, tunable lasers, HeNe lasers, and femtosecond lasers, while the incoherent source link brings you to a selection of LEDs, white light, and broadband SLD sources. The Quantum Electronics category includes optical amplifiers, modulators, and gain elements that are frequently used in research and OEM applications. All of our light sources and optical amplifiers are supported by an extensive line of mounts, sockets, TEC controllers, and current controllers.
-
Product
7-WAY Blade & 4 Flat Connector Tester
3536B
-
Peaceful Thriving Enterprise Co Ltd
This is a tester to test the function of the 7 way connector of the vehicle. User simply plug the tester with the 7 way or 4 way connector, and switch on the corresponding function of the vehicle to check if the LED indication has lighted up correctly. Use in the garages, workshops where there is a need to check the configuration of circuit. Widely used to test trailer light circuits on most trucks, boats, trailer campers, caravans, food trucks and other trailers.
-
Product
Loaded Spectrophotometer
DSCD-900
-
DSCD-900 is a highly performance spectrophotometer with test caliber upward. The instrument adopts the geometric conditions of D/8 lighting and observation of CIE recommendations, integration of the full band LED composite light source, double beam optical system, ETC every-time calibration technology, spectral reflectance standard deviation within 0.08, maximum of colorimetric values ΔE*ab is 0.03, to provide all the necessary color formula. It could be widely used for coating, printing, textile, meet plastic, food, medicine, automobile field to meet customers’ measurement requirement.
-
Product
Power Supply 605D-II
-
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
Product
LED Color Sensor
Smart FINN
-
With the expanding use of LEDs in electronics, a quick and effective solution to test LEDs has become more and more vital. Today, the intelligent choice is the SmartFINN™. The Smart FINN™ is the simplest method for measuring the color of an LED on the market. Smart FINN™ delivers full color and brightness readings with speed and ease. The Smart FINN™ is placed in front of the LED under test with no critical spacing or fiber-optic cables to install or maintain.
-
Product
LED Floodlight up to 6000m, 120Vac 10,000 Lumen
U Light
-
The Teledyne Bowtech U light is for use on subsea platforms that operate down to 6000m depths, requiring a 120Vac Ultra- bright 10,000 lumen, LED Floodlight. The 80° wide LED floodlight beam angle is ideal for colour video inspection tasks. Housed in hard anodised aluminium, this deepwater LED floodlight measures in at 82mm Ø by 148.4mm long and comes with thermal protection ensuring that the light does not overheat if accidentally run in air. The U Light has the capability of being controlled externally by normal ON / OFF power switching or by using phase control diming techniques enabling the operator to produce a varying level of light intensity. This extremely robust U Light LED floodlight is ideal for clear visibility in deep depths on larger work class ROVs, Trenchers and Tractors.
-
Product
Video Signal Distributor
MSDS-4416
-
MSDS-4416 distribute four TMDS input signal up to four display devices such as Projector, PDP, HDTV and TFT-LCD without diminution and distortion. The distribution support single/dual 8~16 bit and user can select input signal by press button and make sure being connected input source with led of the front panel.
-
Product
Constant Temperature Integrating Sphere
IS-*MT
-
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
Product
Proximity Sensors
-
Cutler-Hammer® proximity sensors that deliver the results you're looking for. Choose from photoelectric sensors, 2-wire AC and 3-wire DC inductive sensors, sensors with LED indicators, and more.
-
Product
2D Barcode Module
UTC-100P-B
-
Sensor: CMOS sensor with 640 x 480 pixel resolution. Illumination & Aiming: White LED illumination; Red LED dot aimer. Typical Frame Rate: 30 frames per second. Motion Tolerance: Up to 100 cm/s (4 in/s) for 13 mil UPC at optimal focus.
-
Product
Compound Semi | MEMS | HDD Manufacturing
-
KLA has a comprehensive portfolio of inspection, metrology, and data analytics systems to support power devices, RF communications, LED, photonics, MEMS, CPV solar and display manufacturing. High brightness LEDs are becoming commonly used in solid-state lighting and automotive applications, and LED device makers are targeting aggressive cost and performance improvements, requiring more emphasis on improved process control and yield. Similarly, leading power device manufacturers are targeting faster development and ramp times, high product yields and lower device costs, and are implementing solutions for characterizing yield-limiting defects and processes. KLA's inspection, metrology and data analytics systems help these manufacturers control their processes and increase yield.
-
Product
Portable Hand Held Load Cell Indicator
MODEL SSI
-
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
4 CH LED Driver
LED-0401
-
UC INSTRUMENT’s LED-0401 Compact 4 Channel Computer-Controlled Universal LED Drivers are designed to drive a broad range of LED light sources. Maximum 1.5Acurrent can be output to each channel.
-
Product
Primus Epic Interface Kit
LANTAP-10
-
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
Product
PMS-2000 UV-VIS-Near IR Spectrophotocolorimeter (Scientific Grade)
PMS-2000
-
Hangzhou Everfine Photo-E-Info Co., LTD
PMS-2000, with extremely low stray light and greatly high wavelength accuracy, is trusted by high-end laboratories and scientific research institutions. It not only realizes the high-accuracy test of various light sources and fluorescent materials such as LED, energy-saving lamps, halogen lamps, but also be applied to various professional measurement systems, which are widely used in the fields of photobiosafety, medical devices, ultraviolet, infrared, printing, coatings and so on.
-
Product
Surge / DC Hi-Pot Consoles
HC Model
-
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
Product
Optical Spectrum Analyzer
S6362D
-
Saluki S6362D is a high-resolution, large-dynamic, high-speed, high-performance optical spectrum analyzer. It is perfect for testing 600 nm to 1700 nm optical systems, such as DWDM and optical amplifiers. It can also be used for optical active and passive device testing, such as LED, FP-LD, DFB-LD, optical transceivers and optical fibers and fiber gratings and other optical devices.
-
Product
Optic Node With Amplifier
OX 755
-
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes cum Amplifier- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
LED based light source
iQ-LED
-
Image Engineering GmbH & Co. KG
The most flexible, 22 channel, LED based light source is the heart of all adaptive lighting productsCreate your own light by adjusting the 22 channels to your needs. You can simulate standard light sources, reconstruct the daylight distribution from dawn till dusk, create patches of a high saturated color chart, or reconstruct the spectral distribution of a measured light source. By using the individual channels you can even measure the spectral sensitivities of a camera.
-
Product
S2 Unicolor Digital Sensors
ULP-S2 SCC
LED Sensor
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
