Detectors
register the presence of a stimuli.
See Also: Metal Detectors, Particle Detectors, Sensors, Charge Sensitive Preamplifiers, Checkers
-
Product
O/E Converter
TIA-4000
-
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
Product
Non-Contact H.V. Detector
381 HP
-
Standard Electric Works Co., Ltd
● Protection class : IP65.● 7 voltage settings : 120V, 4kV, 15kV, 25kV, 35kV, 46kV, 69kV● Bright LED visual indication● Vibration function● Frequency range : 40~70Hz● Audible indication● Easy-to-prove method● Power source: 9V alkaline battery ● Non-contact detection by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Special ranges are available upon request● Flashlight function● Safety standard : EN 61326-1 CISPR 11● Operating temperature and humidity : 0°C ~ 40°C / 80% R.H. Max. ● Dimensions : 262(L) × 85(W) × 56(D)mm● Weight: Approx. 345g
-
Product
CS/ONH-Analysis
G6 LEONARDO
-
The high-end thermal conductivity detector used for hydrogen and nitrogen analysis allows detection limits in a sub-ppm range (based on 1g sample mass)
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
Valve Leak Measurement System
VLMS
System
The G Systems Valve Leak Measurement System (VLMS) reliably measures slow leaks that are unidentifiable with conventional leak detectors, helping manufacturers test and ensure that critical valves are absolutely airtight.
-
Product
Magnetic Flaw Detector
CDX-Ⅲ
-
magnetic particle flaw detector is the self-designed magnetic participle flaw detector of MITECH CO.,LTD. With small size, light weight, easy operation, multifunction in one unit. The detector can equip A, D, E O four types of probes to realize the functions of magnetic clamp detection, electromagnetic yoke detection, cross magnetic yoke detection, ring detection. It is the necessary detector to do quality control, safety check, life evaluation in the fields of petrol, chemicals, metallurgy, shipbuilding, aviation, railway etc
-
Product
Rapid Automated Modular Microscope
RAMM
-
Applied Scientific Instrumentation
*Featuring automated high-speed XY stages, precision piezo & motorized Z focusing, and a wide range of scanning options.*Configurable with infinity-corrected optics, dichroic filter cubes, multi-wavelength excitation and emission filterwheels, shutters, and detectors including cameras and photomultipliers.*Auto-focus, focus stabilization, tracker, and robotic specimen loader available.*Arrangement provides a solid platform for high throughput screening, genetic sequencing, experimental research, and much more.*Designed for flexible cost-effective OEM development using high quality high MTBF components to reduce cost and increase customer satisfaction.
-
Product
Ignition Pulse Detector
IP-3100
-
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
Product
Metal Cover Locator
CS880
-
The CS880 Metal Cover Locator is a metal detector that will locate lost or hidden metal objects. It is most commonly used for locating manhole covers through tarmac and grass.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Marine Fuel Sulfur Analyzer
NEX QC MFA
-
Applied Rigaku Technologies, Inc
Specifically designed for marine fuel applications, the new Rigaku NEX QC MFA features an intuitive "icon-driven" touch screen interface for easy operation and a built-in printer for convenience. The shuttered 50 kV X-ray tube and Peltier cooled semiconductor detector deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability (50 kV), along with multiple automated X-ray tube filters, provides an analysis of sulfur (S), nickel (N), vanadium (V), iron (Fe) and zinc (Zn) ... all with low limits-of-detection (LOD).
-
Product
Transmissive Optical Encoder Module
EM1
-
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
Dynatrol® Level Switch for Extremely Lightweight Bulk Solids
CL-10GSS
-
Dynatrol® CL-10GSS Level Detector may be used for high-, intermediate-, or low-point level detection of bulk solids. It is constructed to handle extremely light weight applications that are difficult to measure like glass fibers, glass wool, paper dust, polyester powders and polymer powders. The CL-10GSS is typically used with bulk solids in the density range of more than 5 lbs/ft3.
-
Product
Fuel Density Meter
FD-5110
-
By connecting with the FM-3100 Digital Flow Meter, the FD-5110 Fuel Density Meter can measure temperature and density data in real time. In addition, the FP series Volumetric Flow Detectors with wide range ability and the FD-5110 are the best choice for achieving the accurate mass flow measurement.
-
Product
X-Band Motion Detector
32213
-
The X-Band Motion Detector’s sensor is a common component in security systems and automatic door openers and can detect movements within a room, yard, or even on the other side of a wall. The X-Band Motion Detector operates in the X-band frequency, at 10.525 GHz and indicates detected movements with oscillations in its high/low output. Sensitivity is manually adjustable with a potentiometer, offering direct line of sight detection from roughly 8 to slightly over 30 ft (~2.4 to 9+ m).
-
Product
Low-Barrier Schottky Diode Detector, 10 MHz to 18 GHz
8473B
-
The Keysight 8473B Low-Barrier Schottky Diode (LBSD) detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking.
-
Product
Data Acquisition Recorders & Loggers
DAS1800
-
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
Product
Calibration Standards, Calibration Services
-
ISO 17015 traceable calibrated reference lamps, detectors and reflectors for the calibration and adjustment of sensors and measurement devices for light, optical radiation and light reflection. We offer as well many ISO 17025 calibration services.
-
Product
POWER PROBE 4 MASTER KIT
PPKIT04
-
*Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit testing capabilities*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)*Tests fuel injectors, module drivers (transistors) and works as a circuit detector with the PPECT3000
-
Product
Switched Amplifier With Analog Detector Output
-
Operates at 3 GHz-10 to -5 dBm Input Power to +4 to +7 Output powerAnalog Detector OutputTTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch
-
Product
Phantom Lumber Metal Detector
-
Ideally suited for scanning whole logs and for chipper protection, the Phantom Lumber Metal Detector is a large scale metal detection solution built rugged for the lumber industry. Lumber systems provide an effective means of detecting metal objects typically found in the application, such as fencing wire and nails.
-
Product
Automated Total Nitrosamine Analyser
-
Ellutia Chromatography Solutions
Nitrosamines are carcinogenic compounds that can be found and formed in many products. This has been a particular issue in the pharmaceutical industry recently. Traditional approaches to the analysis, such as by mass spec, have been challenging due to the low detection levels required, the possibility of false positives, or even missing. This system takes a unique approach of using the combination of a chemical reaction targeting nitrosamine compounds, then detection by a detector with very high selectivity and sensitivity for nitro/nitroso compounds. Rather than speciating the various nitrosamines present, the system gives a single quantitative result down to 1 ppb for the total nitrosamine content. This means both volatile and non-volatile nitrosamines are measured at the same time. This process is automated to allow a high sample throughput. This makes it ideal for screening a large number of samples rapidly.
-
Product
Laser energy meter with high dynamic range
PM 200
-
In the past laser energy meters often required a whole selection of pyroelectric detectors for measuring different energies. From this point of view the PM 200 is a very modest instrument. A single detector enables monitoring of energies from the detection limit at 3 ?J up to highest energies of 200 mJ. The active sensor area with an aperture diameter of 34 mm ensures simple and reliable alignment for the detection of large beam profiles.?
-
Product
Personal radioactivity detector
EcotestVIP
-
EcotestVIP is the one and only premium class dosimeter in the world. Created by the leading specialists for successful people who put high value on their own safety. The monitoring device is a combination of the best technical specifications and elegant design.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 LCC
-
A single-channel silicon-based thermopile in a LCC package for surface mount assembly in a small active area of 0.61mm x 0.61mm. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature chang
-
Product
Crack Detectors
-
GAOTek offers a large selection of crack detectors which are affordable, easy to operate and user-friendly. For some industries such as aviation, civil, infrastructure and space technology, even the slightest crack can lead to risks of hazards. There have been cases in the past where projects costing billions were destroyed in seconds due to a minute crack on the surface of the body. GAOTek provides trustworthy devices with various features that are helpful in detecting the smallest crack on an object.
-
Product
optical liquid leak detection system
LEAKLEARN®
-
The LEAKLEARN OPT liquid leak detection system incorporates fluoropolymer optical fiber sensors and detectors, emitting light when fluoropolymer optical fiber sensors contact liquid. T
