-
Product
10-CH Pneumatics CAN
YAV90PNE
-
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
-
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
-
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-01
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
-
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
10-Ch Pneumatics Selftest Module
YAV90PNT
-
Use this module in your self test diagnostics fixture. The YAV90PNT can be used as counterpart of the YAV90PNE, to test that is working properly.
-
Product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
-
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PXI CAN Interface Module
-
PXI CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate, Low-Speed/Fault Tolerant, and/or Single Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from FIBEX and DBC files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
CAN Interface Device
-
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
-
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
-
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
CAN Logger
-
Reach Technologies' CAN Logger is a high performance, high channel count, DSP enabled, automotive bus data logger. The CAN Logger is ideal for capturing all or specific bus traffic for vehicles under test. The CAN Logger is also perfect for real-time monitoring of specific signals.
-
Product
C Series CANopen Interface Module
-
The C Series CANopen Interface Module is a high-speed interface for developing CANopen applications. CANopen is a higher-level communication protocol based on the controller area network (CAN) physical layer. It was designed for motion-oriented machine control networks, but now it is used in a variety of products and applications, including medical equipment, maritime electronics, building automation, and more. The C Series CANopen Interface Module can transmit and receive process data objects (PDOs) and service data objects (SDOs) according to CiA-DS 301. Using the NI-Industrial Communications for CANopen driver, you can batch edit SDOs, configure slave nodes with LSS services support, as well as perform network management (NMT), heartbeat, node guarding, and CANopen synchronization functions.
-
Product
sbRIO-9853, Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module
780923-01
-
Non-Enclosed, 2-Port, High-Speed C Series CAN Interface Module—The sbRIO‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA‑based applications with the NI‑RIO driver on CompactRIO. These modules are ideal for low-level FPGA‑based control and triggering applications that are programmed using the NI LabVIEW FPGA Module. These modules also are ideal for byte-level manipulation of CAN frames in the NI LabVIEW FPGA Module. The sbRIO‑9853 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
-
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
Product
CAN MiniModules
-
Measurement points distributed throughout a device under test, whether in a vehicle or at a test bench place high demands on the measurement technology. Measurement modules must be compact, robust, reliable, and easy to use. CSM meets all these requirements with its long-term proven CAN MiniModule series.
-
Product
NI CAN Single Termination, High-Speed/FD Cable, 2m
192017-02
-
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
USB CAN Interface Adapter
COMMDongle
-
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
Product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
-
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
NI-9862, CAN Interface Module
781639-01
-
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
CAN, CANopen, J1939 Tester
X-Analyser3
-
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
Product
CAN PT MiniModule evo
-
CSM offers these modules for temperature measurements with increased accuracy requirements compared to thermocouples. PTMM evo modules allow high-precision temperature measurements with either PT100 or PT1000 RTD elements.
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
CAN + OBD Network Data Converter
NC2
-
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
Product
2-Port CAN Module
AMAX-5495
-
2-ch CAN portSupport CAN2.0B, compatible with CAN2.0AData Transfer Rate: 1Mbits/sOptical isolation protection of 2,500 VDC ensures system reliability
-
Product
CAN Bus & ARINC-825 (825CAN)
-
The 825CAN module is an intelligent multichannel ARINC 825 (CAN bus) interface module for the multiprotocol Excalibur 4000 & 8000 family of carrier boards. The module supports up to ten ARINC-825 channels. In receive mode, the module stores all or selected messages with status and Time Tag information appended to each message. In transmit mode, the module operates via a transmit Bandwidth Frame which allows scheduling of data transmissions and reduces the need for host computer intervention.
