Optical Switches
Route signal transmitted through optical fiber among optical circuits.
-
product
DCA-M 10 GHz/14 GHz Optical & Electrical Sampling Oscilloscope
UC9110/UC9115
The UC INSTRUEMNTS UC9110/UC9115 DCA-M 10 GHz/14 GHz Optical & Electrical Sampling Oscilloscope is a high speed, performance, flexible one channel optical/electrical that can operate from 1.0 to 14.0 Gb/s (consult factory for higher or lower operation speeds). It is also a stand alone Eye-diagram analyzer test.
-
product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Transmissive Optical Encoder Module
EM2
The EM2 provides digital A & B quadrature outputs with a third output index channel. Each EM2 module is resolution specific and is matched to the resolution of a code wheel. The EM2 operates with a single 5V supply and provides single ended outputs which are capable of both sinking and sourcing 5mA. An internal 0.1 uF decoupling capacitor is designed into the EM2 to provide enhanced noise immunity.
-
product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
Handheld Optical Power Meter
X5001
Optical power meter X-5001 is designed to meet the high demand. It intergrades the handheld optical power meter and the intelligent optical power meter in one unit. It can be used for the absolute power measurement and relative measurement of the link loss in dB. Its compact size, friendly operation interface, broad power measurement range, high precision and brand-new user automatic calibration function and high performance in application makes it an ideal tool for optical fiber network.
-
product
Dual Passive Switches
MAX4888C
Supports Multiple High-Speed Interfaces up to 8.0Gbps While Maintaining Signal Integrity in the Application
-
product
LXI 16:1 Optical MUX LC Single Mode
60-850-413
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Optical Fiber Type Hot Phosphoric Acid Concentration Monitor
CS-620F
In 3D NAND manufacturing process, dozens of layers of SiO2 and SiN are deposited, and the SiN layer is selectively removed using hot phos.In this process, the desired etching rate can be achieved by controlling the concentration and temperature of the chemical solution.Previous products have difficulty to measure high temperature chemicals, but the CS-620F is able to measure at high temperatures up to 170 C degrees.
-
product
400x Bench-Top Optical Fiber Microscope - FTM-400X
Shanghai Fibretool Technology Co.,Ltd.
With coaxial illumination optic magnify system, FTM-400X can easily find the slight defects and scratches on fiber endface. High resolution image sensor and 8"pure black and white digital TFT LCD can show the most real details of fiber endface.This is an integrated fiber endface inspector, it combines optical microscope and monitor in a body other than separate designs. It has clear images and long life time. it has series of adaptors for various kinds of connectors such as multi fiber connectors, optical components. It is an essential instrument for optical manufacturing.
-
product
RS232 / RS485 / RS422 / Serial To Multi-Drop Fiber Optic Converters
Our advanced, rugged, industrial-grade, RS232 / RS485 / RS422 serial to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the RS232 / RS422 / RS485's distance to 3 miles (5km) for multi-mode converters and cables, or 25 miles (40km) for single-mode converters and cables. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire data network more robust and reliable. These multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, and FC connectors.
-
product
PXI Dual 2 Channel Fibre Optic SC/PC
40-855-222
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
RS232 / RS485 / RS422 To Fiber Optic Converters
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
product
UltraCMOS SP12T RF Switch
PE42512
The PE42512 is a HaRP™ technology-enhanced absorptive SP12T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42512 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
2X8 PXIe Switch Matrix, 300 KHz to 9 GHz
M9165B
M9165B 2X8 PXIe switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution.
-
product
3U VPX 1/10/40 Gigabit Ethernet Switch
ComEth4081e
Powered by a Marvell highly integrated System-on-a-Chip (SoC) with programmable packet processors, and controlled by Switchware, the field-proven Interface Concept network management application, the ComEth4080e offers a high density of 1GbE/10GbE and 40GbE ports on a 3U footprint.
-
product
Distribution Board, For 8 N181x SPDT Switches
Y1150A / 34945EXT
Connects the 34945EXT to 8 N181x SPDT to route the power and control signals from the driver module to the switches
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
product
Transmissive Optical Encoder Module
EM1
The EM1 is a transmissive optical encoder module designed to be an improved replacement for the Avago HEDS-9000 series encoder module. This module is designed to detect rotary or linear position when used together with a code wheel or linear strip. The EM1 consists of a lensed LED source and a monolithic detector IC enclosed in a small polymer package. The EM1 uses phased array detector technology to provide superior performance and greater tolerances over traditional aperture mask type encoders.
-
product
Optical Time Domain Reflectometry
OTDR600
The OTDR600 is an optical time domain reflectometry (OTDR) system for the measurement of attenuation and length of optical fibers. The OTDR600 is specifically designed for use in factories and laboratories where high linearity and productivity on factory spool lengths are crucial.
-
product
Hand-Held Optical Power Meter
HOPM-3208
Hangzhou Huatai Optic Tech. Co., Ltd.
With six wavelength calibrating spots (980nm, 1310nm, 1490nm, 1550nm, 1590nm and 1610nm), refined design, easy operation, linearity or non-linearity display, unique FC/SC/ST all-purpose connector, HOPM-3208/HOPM-2650A is the earliest self-developed hand-held optical power meter of Huatai, which can be used for direct optical power measurement as well as relative measurement of optical link loss. It’s an essential test instrument in Optical Communication, CATV system construction and maintenance.
-
product
Analog Optical Power Meter - PXI
Power 1500 Series
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
product
PXI Switch - 4x8 2-Wire Matrix Module
PXI-7931
ADLINK PXI-7931 is a matrix module with 32 cross-point 2-wire relays (DPDT, 2 Form C). The default configuration of the PXI-7931 itself is a 4-group 2x4 2-wire matrix. With the termination board, TB-6231, users could flexibly choose one of the configurations: one 4x8, two 4x4, one 2x16, two 2x8 and four 2x4. Any contact of the PXI-7931 can connect to other contacts, individually or in combination. The PXI-7931 matrix module simplifies the wiring and makes it easy to change the internal connection path. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7931, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
Optical Profilometers
Profilm3D® and Zeta™ optical profilometers provide fast, easy, non-contact solutions for 3D surface topography measurements. Our portfolio of optical profilers supports a variety of measurement techniques, including white light interferometry, True Color imaging and ZDot™ confocal grid structured illumination. KLA Instruments can help guide you to the right optical profiler solution for your unique needs.
-
product
Optical Balloon Theodolite
F. W. Breithaupt & Sohn GmbH & Co.KG
*Robust instrument*Bright scope with wide field occular and fix focus*Magnification 16x (20x optional)*Field of view 55,6m/1000m (optional 27,8m)*Open finder sights*Double vertical circles (reading from both sides of the instrument)*Reading of circles 0,1°*Convenient targeting through friction-controlled by endless wormdrive screws*Accessories upon request like alarm clock, filters, tripod etc.*Long life cycle, full spare part availability*Made in Germany
-
product
LXI 8:1 Optical MUX SC Loop-Thru
60-851-221
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Fiber Optic Network Test
Test and characterize fiber optic cables, assemblies and network with unmatched speed, precision and spatial resolution. Luna’s OBR reflectometers can analyze loss with a spatial resolution and sensitivity unmatched in the industry.
-
product
HV Switch Operating Power
HTDY-H / 393
Wuhan Huatian Electric Power Automation Co., Ltd.
Dedicated power supply designed for inspection and maintenance of high voltage circuit breakers and their operating mechanisms.
-
product
PXI Quad 2 Channel Optic Mux LC
40-855-442
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
