Soil Moisture
See Also: Soil, Moisture, Soil Resistivity
-
Product
Soil Moisture
-
The wireless solution for mobile moisture measurement with TRIME-PICO probes.
-
Product
Soil Moisture Sensor
Modbus RS485
-
This is a contact-less capacitive soil moisture sensor, a continuation of my I2C soil moisture sensor. This particular version of the sensor is suited for more professional installations where long cable runs is a requirement. It adds a local voltage regulator to mitigate the voltage drop and RS485 transceiver to accommodate long wires, also reverse polarity and an additional ESD protection level is added.
-
Product
Soil Moisture Sensor
SoilWatch10
-
SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.
-
Product
SparkFun Soil Moisture Sensor (with Screw Terminals)
-
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
Product
Soil Moisture, Temperature, and EC Sensors
-
Soil volumetric water content probes (sometimes referred to as soil moisture sensors) measure the water content of soil. These probes can be used to estimate the amount of stored water in a profile or how much irrigation is required to reach a desired amount of water in the soil. These probes can be used for quick measurements or installed for long-term measurements.
-
Product
Soil Moisture Loger Sensor
NUL-229
-
This logger sensor is based on measuring the partial vacuum pressure in a tensiometer. A tensiometer is a closed tube with a special ceramic part in its end. The tensiometer is filled with water and put in the soil. If the soil is dry, water goes out by diffusion through the ceramic holes and partial vacuum pressure is created in the tensiometer. When we wet the soil, the partial vacuum in the tensiometer pulls water into the tensiometer and the vacuum decreases. This is why soil moisture is measured in pressure level.
-
Product
SparkFun Soil Moisture Sensor
-
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be and will result in a lower resistance, and a higher SIG out.
-
Product
I2C Soil Moisture Sensor
-
Capacitive soil moisture sensor interfaced via I2C. Additionaly provides ambient light and temperature readings. Open Source Hardware. Soil moisture sensing, Light sensing, Temperature sensing.
-
Product
Soil Testing Instruments
-
Soil water hardness meter, soil moisture meter, soil nutrient tester, soil salinity tester, soil water potential tester
-
Product
Soil Moisture & Temperature Sensor
Mini-Logger
-
The PlantCare Mini-Logger is a maintenance-free sensor which records soil moisture and soil temperature. A USB stick is used to easily program the mini-logger and readout the data. The PlantCare DataViewer Software allows a quick and easy display and analysis of the measured data. Fields of application are scientific research, agriculture and garden and landscaping construction.
-
Product
Soil Sensors
-
Delta-T Devices has decades of experience in creating premium-grade equipment for soil moisture measurement and recording. Our soil moisture sensors, data loggers (with cloud connectivity) and readout units are built to exacting standards ensuring ruggedness, longevity, and optimum performance throughout their life. They are used and trusted by researchers around the world and are suited to a wide variety of applications and budgets.
-
Product
Battery Data Logging Device
FST-AM
-
Foresight Electronics Co., Ltd.
A data logger, is an electronic instrument that records measurements at set intervals over a period of time. Depending on the particular data logger, measurements can include: air temperature, relative humidity, AC/DC current and voltage, differential pressure, time-of-use (lights, motors, etc.), light intensity, water temperature, water level, dissolved oxygen, soil moisture, rainfall, wind speed and direction, leaf wetness, pulse signals, room occupancy, plug load, and many more.
-
Product
Fertilizer / Moisture / Temperature Soil Sensor
-
The sensor can remain permanently in the ground and transmits the measured data wirelessly over an IoT net to a server or to a local control center, where they can be used for large area monitoring of soil data (big-data) and also for the automatic control of irrigation and for precisely dosed fertilization. In addition to the total fertilizer content, the sensor can measure the content of nitrogen, potash and the pH value.
-
-
Product
Soil Mechanics
CECAP
-
Ce.Ca.P. is a complete package for the analysis and design of foundations; because of its completeness, flexibility ad user-friendliness it is a fundamental instrument for any kind of geotechnical project.
-
Product
Moisture Analyzer
LSC-Series
-
Napco Precision Instruments Co
Moisture Analyzer is configured on the basis of high-precision electronic balance weighing sensor and high-efficiency secondary heat radiation device, Moisture analyzer can achieve rapid and accurate determination of the water. Moisture analyzer is a thermodynamic theory based on the material after drying by the weight and wet weight than the percentage of access to content and gouache other results.
-
Product
Moisture Analyzers
V-Series
-
The MIDAC V-Series is designed to detect lower moisture levels than ever before...so you can raise your standards for purity higher than ever before! It's true, MIDAC's V-Series Moisture Analyzers provide unprecedented capability for detecting moisture and other impurities in corrosive gases.
-
-
Product
Moisture Measurement
-
Moisture: The presence of moisture within a material will result in poor adhesion, premature coating failure and poor appearance. For example, applying a powder coating to a damp wooden panel will cause steam to be created when the panel passes through the curing oven, thus causing damage to the coating. It is not sufficient to simply ensure that the surface is dry by touch. The surface of the substrate is often the driest point due to evaporation. It is important to establish the moisture content within the substrate itself. The moisture measurement can either be taken using a Pin moisture meter or Pinless (Contact-Type) moisture meter.
-
Product
Soil Testing Complex
GEOMehanika-M
-
The developed measuring complex for testing soils with "GEOMECHANIKA-M" stamps includes:Control and registration unit: measuring station based on NI cRIO equipment, MIDA overpressure sensor, wireless access point AWK-3131-EU-T, pneumatic system based on pneumatics CamozziLinear motion sensorsWireless Operator Console TestSet of connecting cables
-
Product
Pin Moisture Meter
-
Pin meters can measure all thicknesses from veneer to logs, flat boards or round and oddly shaped pieces, obtain surface and core measurements. Adding electrodes, pins (up to 7″) optimizes usage. For green, air-dried and kiln-dried lumber.
-
Product
Unibloc Moisture Analyzer
MOC63u
-
In many fields, a moisture analyzer is a necessary tool for quality control requirements. With the MOC63u, you can easily obtain accurate data. Simply place material on the pan and shut the cover. The MOC63u will start to measure. The MOC63u adapts to various materials and increases your work efficiency.
-
Product
Soil Gas Flux Solutions
-
From idea to understanding, LI-COR has your soil gas flux research covered. No other solution is as flexible or delivers the same level of proven hardware, gas analyzers, and advanced data analysis software.
-
-
Product
Moisture Analyzer
5812
-
The 5812 moisture analyzer is designed specifically to meet the needs of the natural gas industry for reliable, low-maintenance, self-verifying moisture analysis, with a rapid response to moisture changes.
-
Product
Moisture Analyzers
-
Moisture analyzers provide high-speed measurements and precise analysis on a diverse range of product samples.
-
Product
Microwave Moisture Meter
RX-95
-
The system works based on the absorption of microwave energy by water molecules contained inthe x-rayed material. It is a non-contact, non-destructive method of instant measurement of water content - used for materials such as coal, flour, grain, cement, seeds, sugar, etc. Thanks to high measurement sensitivity (resolution greater than 0.01% of water content by weight), short measurement time (about 5 times/sec.) and repeatability of measurement - the system is suitable for continuous measurement of material moisture, e.g. on conveyor belts and its recording on a PC or using a 4-20 mA current loop.
-
Product
Moisture Meters
-
Moisture meters are used to measure the percentage of water in a given substance. This information can be used to determine if the material is ready for use, unexpectedly wet or dry, or otherwise in need of further inspection.
-
Product
Pinless Moisture Meter
-
A large number of boards can be scanned quickly without leaving pin holes. No effort is needed to insert pins into hard wood.Pinless moisture meters measure lower moisture contents in hardwoods than pin moisture meters.
-
Product
Soil Heat Flux Sensors
-
Soil heat flux sensors may consist of several thermocouples whose measurements are averaged, a single thermopile, or a single thermopile with a film heater. These sensors measure the rate of energy transferred through a surface. Data regarding the amount of energy stored in soil as a function of time is used in energy-balance and Bowen-ratio flux systems.
